ComAp InteliPro

To Next Page

To Previous Page

Written by Tomas Jelen

Prague, Czech Republic

ComAp a.s.

Kundratka 2359/17, 180 00 Praha 8, Czech Republic

Tel: +420 246 012 111, Fax: +420 246 316 647

E-mail: info@comap.cz, www.comap.cz

Application Guide

InteliPro

Protection Relay for Parallel Applications

Application Guide

SW version 1.4, April 2014 – rev. 1

Main Page

Installation and Operation Guide2
Application Guide2
Communication Brochure2
Table of Contents4
Introduction5
Warnings5
Installation Data6
Unpacking the Unit - What Is in the Package6
Mechanical Mounting6
Terminal Diagram7
Voltage and Current Inputs7
Low Voltage Measurement Wiring8
High Voltage Measurement Wiring9
Current Measurement Wiring9
NVD and SYNC Check Wiring10
Complete Measurement Wiring Scheme with Voltage Transformers11
Mains11
Complete Measurement Wiring Scheme Without Voltage Transformers12
Binary Inputs13
Wiring of Binary Inputs13
Binary Outputs14
Analog Inputs14
Wiring of Analog Inputs15
Tristate Inputs15
Relay Card CT2-REL2 Plug-In Module16
Relay Outputs16
Current Inputs16
Power Supply17
Recommended Wiring17
Configurability18
Configuration Parts18
Principle of Binary Inputs and Outputs Configuration18
System of Optional Functions19
Entering the SW Dongle20
User Interface21
Control and Navigation Pushbuttons - Basic Operation21
General Operation Using Buttons21
Passwords21
Signalization Leds22
Status LED Signalization22
Operation Mode with 1 Common Trip Output25
Operation Mode with 2 Trip Outputs26
Priority Switching26
TRIP and Fault Reset Description27
TRIP Event27
TRIP Status27
Fault Reset27
Shared Peripheries28
Protective Functions29
How to Set up Trip Outputs29
How to Set up Blocking Conditions29
Protective Functions in Detail30
Overvoltage, Undervoltage (ANSI 59, 27)30
Voltage Hysteresis for Overvoltage30
Overfrequency, Underfrequency (ANSI 81 H, L)31
Voltage Hysteresis for Unervoltage31
Frequency Hysteresis for Overfrequency31
Voltage Unbalance (ANSI 47)32
Floating Average Overvoltage32
"Loss of Mains" Protections32
Vector Shift (ANSI 78)32
Rate of Change of Frequency (Df/Dt, ROCOF, ANSI 81R)33
Overcurrent: Definite-Time, IDMT and with Voltage Control34
Definite Time Overcurrent (ANSI 50)34
IDMT Overcurrent (ANSI 51)34
Time Overcurrent with Voltage Control and Restraint (ANSI 51V)37
Time Multiplier - ANSI Moderately Inverse37
Earth Fault Current (ANSI 50N, ANSI 51N)38
Ground Surge Current (ANSI 50GS, ANSI 51GS)38
Current Unbalance (ANSI 46)38
Directional Overcurrent (DOC, ANSI 67)38
Neutral Voltage Displacement (NVD, ANSI 59N)39
Directional Power (ANSI 32)40
Synchro Check (ANSI 25)40
AC Reclosing (ANSI 79)40
Pole Slip (ANSI 78PS)40
Dynamic Grid Support41
QU (Undervoltage Dependent Directional Reactive Power) Protection41
CAN Bus and RS48544
Recommended CAN/RS485 Connection45
CAN Bus Connection45
RS485 Connection46
Shorter Distances46
Longer Distances47
Surge Hazard47
Communication Modules48
Il-Nt-23248
Il-Nt-Rs232-48548
Il-Nt-S-Usb49
Il-Nt-Aio49
How to Set up the IL-NT-AIO Module in Liteedit50
IB-Lite53
How to Set up the IB-Lite Module54
Reference Guide57
Library of Binary Inputs63
Binary Alarm and Functional Input Configuration Items63
Functional Input Configuration Items63
Alarm64
CB1 Feedback64
CB2 Feedback64
F.R. Button64
Block 1, Block 265
Ctrlhbeat Sens65
Library of Binary Output Functions66
Common Alarm66
Comm Trp66
Bak Comm Trp66
Bak Trp 167
Bak Trp 267
Dyn Volt Prot68
Ctrlhbeat FD68
QU Gen Prot68
QU Mns Prot68
IGS Prot69
DC Healthy69
Watchdog69
Ctrl Heartbeat69
DOC Sig70
DOC Test70
NVD Sig70
P Sig70
CB1 Protection71
CB2 Protection71
Self Test71
Mains OK71
Aix Wrn/Trp Sig, IOM Aixwrn/Trp Sig72
Bix Status, IOM Bix Status72
Library of Setpoints73
Basic Settings73
Mains CT Ratio73
Mains CT Polar73
Nomvolts Ph-Ph74
Nominal Freq74
Nominal Power74
Nominmainscurr74
Comms Settings75
Contr. Addr75
COM1 Mode75
COM2 Mode75
Iblite IP Addr76
Iblite Netmask76
Iblite Gateip76
Iblite DHCP76
Contr Mailbox77
Time Zone77
DNS IP Address77
Protactiv del77
Auto FR del78
Prio Switching78
Ipro-SW Key78
V Unb80
V Unb Trp BO80
Phaserotation80
Ph Rot Trp BO80
Dyn Volt81
Reset Time81
Qu81
Q Min82
QU del 182
QU del 282
QU Trp Gen82
Lom83
Vs Lim83
Rocof83
ROCOF Filt83
LOM Trip del84
LOM Trp BO84
T Curve85
T Trp BO85
V del85
V Curve85
Unb86
Mindiffeval86
V Trp BO86
Nomingencurr [A]86
Efc87
Sync Check90
Upper V Lim90
Lower V Lim90
Voltage Window91
Phase Window91
Freq Window91
Dwell Time91
Block by AR92
Dead V Lim92
Dead T del92
AC Reclosing92
Maxparalltime93
Nominal RPM93
Pole Slip Lim93
PS Trp BO93
IOM Analog in94
SMS/E-Mail94
Wrn Alarm Msg [OFF/ ON]94
Trp Alarm Msg94
Date/Time95
Timestamp Per [Min]95
Sensors Spec95
Library of Alarm Messages96
List of Values98
Mains Measured98
Mains Power98
List of EMC Tests101
Technical Data102
Operating Conditions102
Physical Dimensions102
Standard Conformity102
NVD and Sync Check Measurement103
Remote Communication Interface104
Extesion Modules Interface104
Interface to Other Controllers104
Relay Card CT2-REL2104
Recommended CAN Cables105

ComAp InteliPro - Page 23

Table of Contents

Other manuals for ComAp InteliPro

Related product manuals