Danfoss VLT User Manual

0-37 Display Text 1
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If it is to be displayed permanently, select Display Text 1 in par.
0-20
Display Line 1.1 Small , par.0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small ,
par. 0-23
Display Line 2 Large or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the
LCP to change a character. Use the
◀
and
▶
buttons to move the cursor. When a character is
highlighted by the cursor, it can be changed. Use the
▲
or
▼
buttons on the LCP to change a
character. A character can be inserted by placing the cursor between two characters and pressing
▲
or
▼
.
0-38 Display Text 2
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If it is to be displayed permanently, select Display Text 2 in par.
0-20
Display Line 1.1 Small , par.0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small ,
par. 0-23
Display Line 2 Large or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the
LCP to change a character. Use the
◀
and
▶
buttons to move the cursor. When a character is
highlighted by the cursor, this character can be changed. A character can be inserted by placing the
cursor between two characters and pressing
▲
or
▼
.
0-39 Display Text 3
Range: Function:
0 N/A* [0 - 0 N/A] In this parameter, it is possible to write an individual text string for display in the LCP or to be read
via serial communication. If it is to be displayed permanently, select Display Text 3 in par.
0-20
Display Line 1.1 Small ,par.0-21 Display Line 1.2 Small , par. 0-22 Display Line 1.3 Small ,
par. 0-23
Display Line 2 Large or par. 0-24 Display Line 3 Large . Use the
▲
or
▼
buttons on the
LCP to change a character. Use the
◀
and
▶
buttons to move the cursor. When a character is
highlighted by the cursor, this character can be changed. A character can be inserted by placing the
cursor between two characters and pressing
▲
or
▼
.
0-70 Set Date and Time
Range: Function:
0 N/A* [0 - 0 N/A] Sets the date and time of the internal clock. The format to be used is set in par.0-71 Date Format
and par.0-72 Time Format .
0-71 Date Format
Option: Function:
Sets the date format to be used in the LCP.
[0] * YYYY-MM-DD
[1] * DD-MM-YYYY
[2] MM/DD/YYYY
6 How to program the adjustable frequency
drive
VLT
®
HVAC Drive Instruction Manual
6-20 MG.11.A9.22 - VLT
®
is a registered Danfoss trademark
6

Danfoss VLT Specifications

General

Frequency	50/60 Hz
Enclosure	IP20, IP21, IP55, IP66
Series	VLT
Control Technique	Flux Vector Control
Output Voltage	0-Vinput
Control Method	Fieldbus
Communication Interface	PROFIBUS, CANopen
Protection Features	Overload, Overvoltage, Undervoltage, Short Circuit, Ground Fault
Cooling Method	Liquid Cooled
Storage Temperature	-25°C to +70°C
Relative Humidity	5-95% non-condensing
Altitude	Up to 1000m (3280ft) without derating, up to 4000m (13120ft) with derating
Operating Temperature	-10°C to +50°C (14°F to 122°F)