Data Domain DD400 Series - Page 96

300 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

The License Command

58 DD400 Series Restorer User Guide

Table of Contents

Default Chapter5
- Table of Contents5
- About this Guide19
Chapter 1: Introduction39
- DD400 Restorer Models40
- Applications that Send Data to a Restorer40
- Data Integrity41
- Data Compression41
- Restore Operations42
- Replicator42
- Restorer Hardware Interfaces42
- Licensing43
- User Interfaces43
- Related Documentation43
- Initial System Settings43
- Command Line Interface45
- Graphical User Interface47
- Hardware System-Level Interfaces49
  - Front Panel49
  - Back Panel50
Chapter 2: Disk Space and Backup Software55
- Space Management55
- Estimate Use of Disk Space56
- Reclaim Data Storage Disk Space57
- Manage File System Use of Disk Space57
- Display the Space Usage Graphs59
Chapter 3: Installation61
- Site Requirements62
- Hardware Installation63
- Backup Software Requirements66
- CIFS Backup Server Timeout66
- DHCP Server66
- Login and Configuration67
- Additional Configuration78
- Administering a Restorer79
  - Command Line Interface79
  - DDR Manager79
Chapter 4: Dd400G Gateway81
- Command Changes82
- Installation85
- Troubleshooting87
Chapter 5: Configuration Management89
- The Config Command89
- The License Command94
Chapter 6: Access Control for Administration97
- Add a Host97
- Remove a Host97
- Enable a Protocol98
- Disable a Protocol98
- Reset System Access98
- Add an Authorized SSH Public Key98
- Remove an SSH Key File Entry99
- Remove the SSH Key File99
- Create a New HTTPS Certificate99
- Display the SSH Key File100
- Display Hosts and Status100
- Return Command Output to a Remote Machine100
Chapter 7: User Administration103
- Add a User103
- Remove a User103
- Change a Password104
- Reset to the Default User104
- Display Current Users104
- Display All Users105
Chapter 8: Alerts and System Reports107
- Alerts108
- Autosupport Reports112
- Hourly System Status116
Chapter 9: File System Management117
- Statistics and Basic Operations117
- Clean Operations121
Chapter 10: Disk Management129
- Fail a Disk129
- Unfail a Disk130
- Check All Disks130
- Identify a Physical Disk in the Chassis130
- Display Disk Status130
- Display Disk Type and Capacity Information131
- Display RAID Status for Disks132
- Display Detailed RAID Information133
- Display Disk Performance Details135
- Reset Disk Performance Statistics136
- Display Disk Reliability Details136
- Display Disk Debug Information137
- Display the History of Disk Failures137
Chapter 11: System Maintenance139
- The System Command139
- The Alias Command149
- Time Servers and the NTP Command150
Chapter 12: Network Management153
- The Net Command153
- The Route Command163
Chapter 13: NFS Management167
- Add NFS Clients167
- Remove Clients168
- Enable Clients168
- Disable Clients168
- Reset Clients to the Default169
- Clear the NFS Statistics169
- Display Active Clients169
- Display Allowed Clients169
- Display Statistics170
- Display Detailed Statistics171
- Display Status171
- Display Timing for NFS Operations172
Chapter 14: CIFS Management173
- Access from Windows to a Restorer173
  - Add a User173
  - Add a Client174
- CIFS Command174
Chapter 15: Replicator183
- Configure Replicator183
- Start Replication184
- Suspend Replication184
- Resume Replication185
- Remove Replication185
- Reset Authentication between the Restorers185
- Move Data to a New Originator185
- Change an Originator Hostname186
- Change a Replica Hostname186
- Add a Scheduled Throttle Event186
- Delete a Scheduled Throttle Event187
- Set a Temporary Throttle Rate188
- Set an Override Throttle Rate188
- Reset Throttle Settings189
- Display Statistics189
- Display Status190
- Display Replicator Configuration191
- Display Throttle Settings191
- Procedure: Set up and Start Replication192
- Procedure: Replace an Originator192
- Procedure: Replace a Replica193
Chapter 16: Backup/Restore Using NDMP195
- Add a Filer195
- Remove a Filer195
- Backup from a Filer196
- Restore to a Filer196
- Remove Filer Passwords197
- Stop an NDMP Process197
- Stop All NDMP Processes197
- Display Known Filers198
- Display NDMP Process Status198
Chapter 17: SNMP Management and Monitoring199
- Enable SNMP199
- Disable SNMP199
- Set the System Location200
- Reset the System Location200
- Set a System Contact200
- Reset a System Contact200
- Add a Trap Host201
- Delete a Trap Host201
- Delete All Trap Hosts201
- Add a Community String201
- Delete a Community String202
- Delete All Community Strings202
- Display SNMP Agent Status202
- Display the System Contact202
- Display Trap Hosts203
- Display All Parameters203
- Display the System Location204
- Display Community Strings204
- Display the MIB and Traps204
Chapter 18: Log File Management205
- Display Log Files205
- List Log Files206
- Scroll New Log Entries207
- Archive Log Files207
- Send Log Messages to Another System208
Chapter 19: Hardware Servicing211
- Customer Operations211
  - Replace Disks212
  - Replace Power Units215
- Operations for Trained Service Personnel218
Appendix A Time Zones229
Appendix B Restorer Commands235
- Adminaccess235
- Alerts237
- Alias239
- Autosupport241
- Cifs244
- Config248
- Disk251
- Filesys254
- Help259
- License260
- Log261
- Ndmp264
- Net266
- Nfs270
- Ntp273
- Replication275
- Route283
- Snmp285
- System288
- User294
- Index295