Datalogic Matrix 120 User Manual (English)

Other manuals for Datalogic Matrix 120

User Guide17 pages

Product Reference Guide188 pages

Questions and Answers:

A
Angela LaraSep 7, 2025
What to do if my Datalogic Matrix 120 always transmits the No Read Message?
- P
  Paul BurgessSep 8, 2025
  If your Datalogic Card Reader consistently transmits the No Read Message, try the following: 1. Run the Rapid Configuration procedure. 2. Position the reader correctly using the guidelines. 3. Adjust the Acquisition Delay on Trigger if the moving code is out of view. 4. Set the Continuous Operating Mode if no external trigger is available. 5. Improve code image quality through Image Setup. 6. Check parameter settings in the Code Setup step for 2D Codes, 1D Codes, and Postal Codes. 7. View the full resolution code image to assess printing or marking quality.
G
George ChambersAug 23, 2025
Why is the data transferred to the host incorrect or corrupted from Datalogic Scanner?
- S
  Sarah BrownAug 25, 2025
  If the data transferred to the host from your Datalogic Scanner is incorrect, corrupted, or incomplete, check the following: * Ensure the host serial port settings match the reader's serial port settings. * Verify the Header and Terminator String parameter settings in the DL.CODE Data Formatting step. * Check the various Message Field parameter settings in the DL.CODE Data Formatting step.
R
Randy JonesAug 25, 2025
How to fix Datalogic Scanner when it is not transmitting data to the host?
- L
  lindseylandryAug 26, 2025
  If your Datalogic Scanner is not transmitting anything to the host, consider these potential solutions: * Check the serial cable wiring to ensure it is correct. * If using CBX, make sure the RS422 termination switch is OFF. * Confirm that the host serial port settings are the same as the reader serial port settings. * In DL.CODE, you can configure the COM LED Function to indicate Main Serial Port TX or Main Serial Port RX under Device menu > Settings > Settings > LED Configuration.
M
Mary ThomasAug 27, 2025
What to do if the POWER LED is not lit on Datalogic Scanner?
- J
  John MossAug 27, 2025
  If the POWER LED on your Datalogic Scanner is not lit, check the following: * Ensure the power is connected. * If using a power adapter (like PG6000), verify it's connected to the wall outlet. * If using rail power, check if the rail has power. * If using CBX, confirm it has power by checking the switch and LED. * Verify whether you are referring to the device/accessory cable or the CBX spring clamp connectors. * Measure the voltage either at pin 1 and pin 2 (for the 17-pin connector) or at the spring clamp Vdc and GND (for CBX).
L
leesamanthaAug 27, 2025
Why Datalogic Scanner doesn't transmit results even when TRIGGER LED is blinking?
- T
  terri04Aug 27, 2025
  If the TRIGGER LED on your Datalogic Scanner is blinking but no result is transmitted, verify the Code Collection parameters in the Reading Phase step and the Data Formatting parameters in the Data Formatting step.
J
Jessica GrayAug 30, 2025
How to improve image clarity on Datalogic Scanner?
- R
  Ryan PerezAug 30, 2025
  To improve image clarity on your Datalogic Scanner, verify the Focus procedure and reading distance.
K
kenneth46Sep 12, 2025
Why isn't the TRIGGER LED blinking when using serial trigger source on my Datalogic Matrix 120?
- D
  david54Sep 13, 2025
  If the TRIGGER LED is not blinking when using a serial trigger source with your Datalogic Card Reader, check the Acquisition Trigger, Reading Phase-ON, and Reading Phase-OFF parameters in the Reading Phase step. Also, verify that the COM port parameters (Baud Rate, Parity, Data Bits, Stop Bits) are correctly assigned. Ensure the settings of Acquisition Trigger String, Reading Phase-ON String, and Reading Phase-OFF String parameters are correct and that the serial trigger source is correctly connected.
G
Garrett PatrickSep 9, 2025
How to fix a blurry image on my Datalogic Matrix 120 Card Reader?
- S
  Stephen PriceSep 9, 2025
  If the image from your Datalogic Card Reader is not clear, verify the Focus procedure and reading distance.
C
Christopher VasquezSep 6, 2025
What to do if my Datalogic Matrix 120 is not transmitting anything via serial communication?
- C
  christina98Sep 6, 2025
  If your Datalogic Card Reader isn't transmitting anything to the host via serial communication, first check the serial cable wiring. If you're using a CBX, ensure the RS422 termination switch is OFF. Confirm that the host serial port settings match the reader's. Also, note that the COM LED Function can be configured to indicate Main Serial Port TX or Main Serial Port RX in DL.CODE Device menu > Settings > Settings > LED Configuration.
A
Anne RamirezSep 4, 2025
How to fix Autorun or Start.hta when it doesn't run during Datalogic Scanner DL.CODE Installation?
- S
  Scott RussellSep 4, 2025
  If Autorun or Start.hta doesn't run during DL.CODE installation for your Datalogic Scanner, check your Windows settings to see if Autorun is disabled. Also, associate the file type .hta with the Microsoft HTML Application host mshta.exe in Windows\System32.

Datalogic Matrix 120 Specifications

General

Type	2D Imager
Light Source	White LED
Aiming System	Laser
Image Sensor	CMOS
Read Capability	1D, 2D
Minimum Resolution	0.1 mm
Interface	USB, RS-232, Ethernet
Operating Temperature	0°C to 45°C
Storage Temperature	-20°C to 60°C
Power Supply	5V DC
Humidity	90% non-condensing
Certifications	CE

Related product manuals

Datalogic Matrix 210N

167 pages

Datalogic Matrix 120 Reference Manual

Table of Contents

Other manuals for Datalogic Matrix 120

Questions and Answers:

Datalogic Matrix 120 Specifications

Related product manuals