Why does the dew point reading seem too high or too low on my Davis Instruments Weather Station?
If the dew point reading on your Davis Instruments Weather Station seems too high or low, check the temperature calibration numbers. Remember that dew point depends on temperature and outside humidity, so ensure those readings are accurate.
What to do if Davis Instruments Vantage Pro2 is not uploading data?
If your Davis Instruments Weather Station isn't uploading data, try these steps: 1. Repower the device by unplugging the main power cable, waiting one minute, and then plugging it back in. 2. Ensure the status LED indicates normal function; otherwise, the device hasn't registered on the network. Check the LEDs. 3. Verify power to the weather station and ensure all cables are securely connected. 4. Measure the battery power using a voltmeter. If the issue persists, further assistance may be needed.
What to do if the Davis Instruments Vantage Pro2 Weather Station display is blank?
If the display of your Davis Instruments Weather Station is blank, it means the unit isn't getting power. You should check the power adapter connections and consider replacing the batteries.
What to do if Davis Instruments Weather Station display locks up?
If your Davis Instruments Weather Station console "locks up", reset it by removing both the AC and battery power, then restore the power. If this happens often when using AC power, plug the AC power adapter into a surge suppressor.
Why is my Davis Instruments Weather Station console sluggish at low temperatures?
If your Davis Instruments Weather Station console is sluggish or not working at low temperatures, it may be because the console and display are not designed to function below 32º F (0º C). Use an external temperature sensor in low-temperature locations or install the console indoors.
Why are the sunrise and sunset times incorrect on my Davis Instruments Weather Station?
If the sunrise and sunset times are incorrect on your Davis Instruments Weather Station, check your latitude, longitude, time zone, and daylight saving time settings. The console calculates these times based on these settings.
Why does the wind speed read 0 on my Davis Instruments Weather Station?
If the wind speed on your Davis Instruments Weather Station reads 0 all the time or intermittently, the problem may be with the anemometer. Test it by spinning the wind cups, check the reed switch fields on the diagnostic screen, and contact technical support.
Why is the wind direction reading dashed out on my Davis Instruments Weather Station?
If the wind direction reading is dashed out on your Davis Instruments Weather Station, and you have a wireless model, check the reception. If you have a cabled model, the cable may be faulty. If these steps don't solve the problem, the anemometer might be faulty, and you should contact technical support.
Why does the outside temperature seem too low on my Davis Instruments Vantage Pro2?
If the outside temperature reading on your Davis Instruments Weather Station seems too low, check the calibration number and adjust if necessary. Also, make sure sprinklers aren't hitting the ISS radiation shield; if they are, relocate it. Refer to the ISS manual for more information.
Why is the dew point reading too high or low on my Davis Instruments Weather Station?
If the dew point reading on your Davis Instruments Weather Station seems too high or low, check the temperature calibration numbers. Dew point depends on temperature and outside humidity, so ensure those sensors are working correctly.
Overview of the console's hardware and capabilities.
Details on optional sensors, stations, and software for the system.
Instructions for powering the console unit.
Procedure for installing backup batteries in the console.
Guidance on optimal placement for accurate readings and visibility.
Steps for securely mounting the console onto a wall.
Guide to configuring station settings and options.
How to view and manage current weather data and units.
How to view recorded daily, monthly, and yearly high/low values.
How to set and manage various alarm conditions.
How to view historical weather data in graphical format.
Solutions for common display and sensor issues.
Procedures for changing batteries and general care.
General| Update Interval | 2.5 seconds |
|---|---|
| Wind Direction Resolution | 1° |
| Wind Direction Range | 0 to 360° |
| Rain Collector | Self-emptying tipping bucket |
| UV Index Range | 0 to 16 |
| Solar Radiation Range | 0 to 1800 W/m² |
| Console Display | LCD with backlight |
| Wireless Transmission Range | 1000 feet (300 meters) line of sight |
| Temperature Range | -40 to 150 °F (-40 to 65 °C) |
| Humidity Range | 1 to 100% |
| Barometric Pressure Range | 16.00 to 32.50 inHg (540 to 1100 hPa) |
| Wind Speed Range | 0 to 200 mph (0 to 322 km/h) |
| Rain Collector Size | 0.01 inch (0.2 mm) resolution |
| Rain Measurement Accuracy | ±4% at rates up to 2 in/hr (50 mm/hr) |
| Power Supply | Solar-powered with battery backup |
| Console Power Supply | AC adapter or 3 C batteries |
To Next Page
