Denon AVR-1312 Getting Started

7
ENGLISHFRANÇAISESPAÑOLPORTUGUÊSESPAÑOLNEDERLANDSSVENSKA
Connect Preparation PlaybackSetup
7
ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA
3
Use ui to select a speaker, and use
o p to select distance.
Front L / Front R / Center / Subwoofer /
Surround L / Surround R / Surround Back Lz /
Surround Back Rz
Select the speaker.
z When the “Speaker Confi g.” – “Surround
Back” (vpage 5) setting is set
to “None”, “Surround Back L” and
“Surround Back R” is not displayed.
• 0.0ft – 60.0ft : Set the distance.
• The speakers that can be selected differ
depending on the “Speaker Confi g.”
(vpage5) settings.
• Default settings :
Front L / Front R / Center / Subwoofer : 12.0 ft
Surround L / Surround R /
Surround Back L / Surround Back R : 10.0 ft
• Set the difference in the distance between the
speakers to less than 20 ft.
NOTE
Speakers set to “None” in “Speaker Confi g.”
(vpage5) are not displayed.
4
Press ENTER to enter the setting.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
Step
Front L/R
Center
Subwoofer
Surround L/R
Speaker Setup
1
Use ui to select “Channel Level”,
and then press
ENTER.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
Test Tone Start
Default
[ ][ENTER] Enter Return
Speaker Setup
Test Tone Start
Default
1 Channel Level
2
Press ENTER.
Output test tone.
Front L
Center
Front R
Surround R
Surround L
Subwoofer
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
0.0dB
[ ][ENTER] Enter Return
1 Channel Level
3
Use ui to select a speaker, and use
o p to adjust the sound volume of
each speaker to be equal.
Front L / Center / Front R / Surround R /
Surround Back Rz / Surround Back Lz /
Surround L / Subwoofer
Select the speaker.
z When the “Speaker Confi g.” – “Surround
Back” (vpage 5) setting is set
to “None”, “Surround Back L” and
“Surround Back R” is not displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• When o is pressed while the subwoofer volume
is set to “–12 dB”, the “Subwoofer” setting
switches to “OFF”.
• When “Channel Level” is adjusted, the adjusted
values are set for all the surround modes. To
adjust the channel level separately for the
different surround modes, use the operation
see vm page 26 “Adjusting the volume of
the speakers“.
NOTE
• Speakers set to “None” in the “Speaker Confi g.”
(vpage5) settings are not displayed.
• When a headphones jack is inserted in the
PHONES jack of this unit, the “Channel Level”
is not displayed.
Default
The “Channel Level” settings are
returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
4
Press ENTER to enter the setting.
Test Tone Start
Default
1 Channel Level
5
Press RETURN B.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
Test Tone Start
Default
Speaker Setup
Default settings are underlined.
Channel Level
Default settings are underlined.
1AVR1312E3ENGIMGS0033rd110120.inddSec:7 2011/01/2111:12:47

Denon AVR-1312 Specifications

General

Number of Channels	5.1
HDMI Inputs	4
HDMI Outputs	1
Amplification Type	Discrete
Input Sensitivity	200 mV
Frequency Response	10 Hz - 100 kHz (+1, -3 dB)
Signal-To-Noise Ratio	98 dB
Digital Optical Inputs	2
Coaxial Digital Input	1
Analog Audio Inputs	4
Headphone Jack	Yes
Tuner Presets	56
Dimensions (W x H x D)	434 x 151 x 319 mm
Amplifier Type	Discrete
Tuner Type	AM/FM
Preset Stations	56
Remote Control	Yes
Dolby Technologies	Dolby Digital Plus, Dolby Pro Logic II, Dolby TrueHD
DTS Technologies	DTS-HD Master Audio
Output Power / Channel	75 W (8 Ohms, 20 Hz - 20 kHz, 2 channels driven, THD 0.08%)
Input Impedance	47 kOhms
Audio Inputs	2 Optical, 1 Coaxial, 4 Analog
Power Output	75W per channel (8 ohms, 20Hz-20kHz, 0.08% THD)