6
ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS ESPAÑOL NEDERLANDS SVENSKA
6
ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA
3
Use ui to select “SW Mode”, and
use
o p to select a detailed setting.
LPF for LFE
SW Mode
120Hz
LFE
1
Bass Setting
SW Mode
Select low range signals to be
reproduced by subwoofer.
• LFE : The low range signal of the channel set to
“Small” speaker size is added to the LFE signal
output from the subwoofer.
• LFE+Main : The low range signal of all channels
is added to the LFE signal output from the
subwoofer.
• “SW Mode” can be set when “Speaker Confi g.”
– “Subwoofer” (vpage5) is set to “Yes”.
• Play music or a movie source and select the
mode offering the strongest bass.
• Select “LFE+Main” if you want the bass signals
to always be produced from the subwoofer.
NOTE
If “Front” and “Center” for “Speaker Confi g.”
are set to “Large”, and “SW Mode” is set to
“LPF for LFE”, no sound may be output from
the subwoofers, depending on the input signal or
selected surround mode.
4
Press ENTER to enter the setting.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
LPF for LFE
SW Mode
Speaker Setup
1
Use ui to select “Bass Setting”, and
then press
ENTER.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
LPF for LFE
SW Mode
[ ][ENTER] Enter Return
Speaker Setup
LPF for LFE
SW Mode
120Hz
LFE
1
Bass Setting
2
Use o p to select the frequency.
LPF for LFE
Set LFE signal playback range.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz /
200Hz / 250Hz
1
Use ui to select “Distance”, and
then press
ENTER.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
Step
Front L/R
Center
Subwoofer
Surround L/R
[ ][ENTER] Enter Return
Speaker Setup
Step
Front L
Front R
Center
Subwoofer
1ft
12.0ft
12.0ft
12.0ft
12.0ft
1
Distance
2
Use o p to change the step (minimum
variable distance).
1ft : For changing in 1-foot steps.
0.1ft : For changing in 0.1-foot steps.
Surround Back
Set the presence, size and
number of surround back
speakers.
• Large : Use a large speaker that can adequately
play back low frequencies.
• Small : Use a small speaker that has inadequate
playback capacity for low frequencies.
• None : Select when the surround back speakers
are not connected.
Even when the “Surround Back“ setting
is other than “None”, sound may not be
emitted from the surround back speaker,
depending on the playback source. In this
case, make “Surround Parameter” – “SB CH
OUT” (vm page 36 “Adjusting the sound
fi eld effects“) setting other than “OFF”.
Subwoofer
Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
When “Front” is set to “Small”, “Subwoofer”
is automatically set to “Yes”.
5
Press ENTER to enter the setting.
Speaker Config.
Bass Setting
Distance
Channel Level
Crossover Freq.
Front
Center
Surround
Surround Back
Subwoofer
Speaker Setup
Speaker Confi g. (Cont.) Bass Setting
Default settings are underlined.
Distance
1AVR1312E3ENGIMGS0033rd110120.inddSec:6 2011/01/2111:12:46
To Next Page
Loading...
Need help?
General
