ENGLISH
Getting Started Connections Playback Remote Control Information Troubleshooting Specifications
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
5
Perform Step 4 repeatedly for the 3rd, 4th, 5th, and
6th measurments.
Once measurements for the sixth position are completed, “All
the measurements were finished.” is displayed.
b Measure at a total of six positions, including the main listening
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
6
Once measurements
are nished, use ui
to select “Calculate”,
then press .
Analysis begins.
b Analysis takes several
minutes to complete.
The time required for
this analysis depends on
the number of speakers
connected. The greater
the number of speakers
connected, the longer
analysis will take.
7
Use ui to select the item you want to check, then
press .
The measurement result
confirmation screen is
displayed.
b Subwoofers or other
speakers may be set to
a value that does not
correspond to the actual
distance.
Step 3 : Performing the Audyssey Auto Setup Procedure
• The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
MultEQ corrects acoustical distortions within the listening area.
• Once started, MultEQ will play a series of test tones through each
speaker.
• Before starting, connect and position all of your speakers.
Step2:Measurement
MultEQ
Retry
Cancel
[ENT]:Cancel
Calculate
All the measurements
were finished.
Step3:Calculating
MultEQ
Calculating
[----------]
Please wait...
⇩
Step4:Check
MultEQ
Please check the results
of the measured item.
Distance Check
Channel Level Check
Crossover Freq.Check
Speaker Config.Check
Next
[ENT]:Select
1
Press ui to select
“Start”, then press
.
Detection of the speaker
configuration starts.
2
Once all the speakers
have been detected
and the screen on
the right appears,
check the results
of detection of the
connected speakers.
3
Once you have checked the results, use ui to select
“Next”, then press .
Measurements for the main listening position begin.
4
Once the screen on
the right appears,
move the setup
microphone to the
second position, use
ui to select “Next”,
then press .
Measurements for the second position begin.
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Normal
Pre Assign:
Start
Cancel
[ENT]:Select [RTN]:Back
Please place microphone
main listening position.
Next
Retry
[ENT]:Next
Front Sp. :Yes
Center Sp. :Yes
Subwoofer :Yes
Surround Sp. :Yes
S.Back Sp. :Yes
:2sp
Step1:Speaker Detection
MultEQ
Step2:Measurement
MultEQ
Please place microphone
Cancel
[ENT]:Next
Next
Calculate
2nd listening position.
at ear height at
1
Press ui to select “Pre Assign”.
2
Press o p to select
Pre Assign Mode.
Normal
: The sound of the surround back channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
Front Height
: The sound of the front height channel is output
from the SURR. BACK / FRONT HEIGHT PRE
OUT connectors.
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Normal
Pre Assign:
Start
Cancel
[ENT]:Select [RTN]:Back
Please place microphone
main listening position.
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Normal
Pre Assign:
Start
Cancel
[ENT]:Select [RTN]:Back
Please place microphone
main listening position.
Changing the PRE OUT connectors assignment
(Pre Assign)
The signals output from the AVR-590’s SURR. BACK / FRONT HEIGHT
PRE OUT connectors can be switched to signals of the surround mode
being used.
n To cancel Audyssey Auto Setup
Use ui to select “Cancel”, then use o p to select “Yes”.
Settings
Step 2 : Audyssey Auto Setup
Preparations
around items indicate the settings made upon purchase.
If adjustment to the environment is necessary, set the following
items before proceeding.
To Next Page
Loading...
Need help?
General
