Denon AVR-1907 Service Manual (English)

Other manuals for Denon AVR-1907

Service Manual102 pages

Specifications2 pages

Questions and Answers:

S
scottvanessaAug 19, 2025
What to do if my Denon AVR-1907 display is on but there's no sound?
- Q
  qmartinAug 19, 2025
  If your Denon Stereo Receiver's display is lit but you're not getting any sound, there could be several reasons: * Check if the speaker cables are securely connected. * Ensure the FUNCTION knob is in the correct position. * Verify the volume isn't set to the minimum; turn it up. * Make sure MUTING is switched off. * Confirm a digital signal is being input and that you've selected the correct digital signal input source.
B
Brian ByrdAug 21, 2025
How to fix no sound from the subwoofer connected to my Denon AVR-1907?
- S
  Steve McneilAug 21, 2025
  If you're not getting any sound from the subwoofer connected to your Denon Stereo Receiver: * Ensure the subwoofer is powered on. * Check that the subwoofer's initial setting is set to “YES”. * Verify the subwoofer's output is properly connected. * Make sure the subwoofer's channel volume level isn't set to “OFF”; turn it up.
J
Jennifer ConradAug 23, 2025
Why is there no sound coming from the surround speakers of my Denon AVR-1907 Stereo Receiver?
- H
  Heather MayAug 23, 2025
  If no sound is coming from the surround speakers of your Denon Stereo Receiver, it might be because the surround mode is set to “STEREO”. Try setting it to a mode other than “STEREO”.
K
Kevin MooreAug 26, 2025
What to do if the display is not lit and no sound is produced when the power switch is on for my Denon AVR-1907?
- J
  Justin CruzAug 26, 2025
  If the display is not lit and no sound is produced when the power switch is on for your Denon Stereo Receiver, check the insertion of the power supply cord plug.
N
Nicole RamirezAug 27, 2025
Why is my Denon AVR-1907 Stereo Receiver not responding to the remote control?
- J
  Jennifer WilliamsAug 28, 2025
  If your Denon Stereo Receiver isn't responding to the remote, consider these possibilities: * The batteries in the remote may be dead; replace them with new ones. * You might be too far from the unit; move closer. * There could be an obstacle blocking the signal; remove it. * Ensure you're pressing the correct button. * Check that the batteries are inserted with the correct polarity.
C
catherinesmithAug 29, 2025
Why does my Denon Stereo Receiver turn off and the power indicator blinks red?
- C
  Christopher LongAug 29, 2025
  If your Denon Stereo Receiver's power has turned off and the power indicator is blinking red, it could indicate: * The unit's internal temperature has risen, activating the protection circuit; place the receiver in a well-ventilated area. * The speaker wires are touching each other or the receiver's rear panel, triggering the protection circuit; check all speaker cable connections. * The receiver may be malfunctioning. In this case, turn off the power and contact a DENON customer service center.
P
Paul MasseySep 1, 2025
What to do if nothing is displayed on the monitor connected to my Denon Stereo Receiver?
- D
  Douglas SmithSep 1, 2025
  If nothing is displayed on the monitor connected to your Denon Stereo Receiver, check the following: * Ensure the receiver's video output terminals and the monitor's input terminals are correctly connected. * Verify that the monitor’s input setting is set to the terminals to which video signals are connected. * If a player is connected with a component terminal and the TV is connected with a video or S-Video terminal, make the interlace settings on the player.
A
Amanda MartinezSep 3, 2025
Why am I not getting DTS sound from my Denon AVR-1907?
- B
  Brooke PayneSep 3, 2025
  If you're not getting DTS sound from your Denon Stereo Receiver, consider these possibilities: * The DVD player’s audio output setting may not be set to bit stream; make the DVD player’s default settings. * The DVD player may not be DTS-compatible; use a DTS-compatible player. * The receiver’s input setting may be set to analog; set it to “AUTO” or “DTS”.
A
Allison KingSep 5, 2025
Why are no test tones being produced by my Denon AVR-1907 Stereo Receiver?
- M
  Matthew TapiaSep 5, 2025
  If no test tones are being produced by your Denon Stereo Receiver, it may be because the surround mode is set to a mode other than STANDARD (Dolby/DTS Surround). Set it to STANDARD (Dolby/DTS Surround).
L
lsandersSep 7, 2025
Why is sound only coming from the center speaker on my Denon AVR-1907 Stereo Receiver?
- D
  Dominique GarrettSep 7, 2025
  If sound is only coming from the center speaker on your Denon Stereo Receiver, it's likely because you're playing a monaural source (TV, AM radio broadcast, etc.) in the STANDARD (Dolby/DTS Surround) mode. When playing monaural sources, select a surround mode other than STANDARD (Dolby/DTS Surround) mode.

Denon AVR-1907 Specifications

General

Speakers connectivity type	-
Equalizer	Yes
Product color	Black
Audio decoders	DTS, DTS 96/24, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital, Dolby Digital EX, Dolby Pro Logic IIx
Apple docking compatibility	iPod
Receiver type	Surround
Audio output channels	7.1 channels
Power output per channel (1KHz@6 Ohm)	120 W
Power output per channel (20-20KHz@8 Ohm)	85 W
Wi-Fi	No