Denon AVR-891 - Listening Mode Selection Guide; Surround Mode Display and Selection; Surround Mode Compatibility Chart

24
ENGLISH
Tuning in radio stations
Listening to FM/AM broadcasts
1
Press TUNER to switch the input
source to “TUNER”.
2
Press BAND to select “FM” or
“AM”.
FM
When listening to an FM broadcast.
AM
When listening to an AM broadcast.
3
Tune in the desired broadcast
station.
q To tune in automatically
(Auto tuning)
Press MODE to light the “AUTO” indicator on the display, then
use TUNING d or TUNING f to select the station you want to
hear.
w To tune in manually (Manual tuning)
Press MODE to turn off the display’s “AUTO” indicator, then use
TUNING d or TUNING f to select the station you want to hear.
n Tuner (FM/AM) operation
Operation buttons Function
CH +, – Preset channel selection
MENU Amp menu
uio p
Cursor operation
ENTER Enter
SEARCH Direct frequency tuning
RETURN Return
BAND FM/AM switching
MODE Switch search modes
TUNING df
Tuning (up/down)
0 – 9
Preset channel selection (1 – 8) /
Direct frequency tuning (0 – 9)
SHIFT Preset channel block selection
MEMORY Preset memory registration
TV POWER TV power on/standby (Default : SONY)
TV INPUT Switch TV input (Default : SONY)
• If the desired station cannot be tuned in with auto tuning, tune it in
manually.
• When tuning in stations manually, press and hold
TUNING d or
TUNING f to change frequencies continuously.
• The time (default : 30 sec) for which the menus are displayed can
be set at menu “TUNER” (vpage61). Press
uio p to return to
the original screen.
n Listening to preset stations
1
Press SHIFT to select the memory
block (A to G).
2
Press CH +, CH – or 1 – 8 to select
the desired preset channel.
You can also operate via the main unit.
In this case, perform the following
operations.
Press TUNING PRESET, then turn SOURCE
SELECT
to select the preset radio station.
n Direct frequency tuning
You can enter the receiving frequency directly to tune in.
1
Press SEARCH.
2
Input frequencies using the 0 – 9.
• If o is pressed, the immediately preceding
input is cancelled.
3
When setting is completed, press
ENTER.
The preset frequency is tuned in.
n Presetting radio stations (Manual preset)
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
• Stations can be preset automatically at “Auto Preset”
(vpage45). If “Auto Preset” is performed after performing “Manual
Preset”, the “Manual Preset” settings will be overwritten.
1
Tune in the broadcast station you
want to preset.
2
Press MEMORY.
3
Press SHIFT to select the block (A
to G) in which the channel (1 to 8
per a block) is to be preset, then
press CH +, CH – or 1 – 8 to select
the preset number.
4
Press MEMORY again to complete the setting.
• To preset other stations, repeat steps 1 to 4.
Default settings
Block (A – G)
and
Channel (1 – 8)
Default Settings
A1 – A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 – B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
C1 – C8 90.1 MHz
D1 – D8 90.1 MHz
E1 – E8 90.1 MHz
F1 – F8 90.1 MHz
G1 – G8 90.1 MHz
Specify a name for the preset broadcast station
(Preset Name) (vpage46)