65
ENGLISH
Basic versionSimple version InformationAdvanced version
Registering preset codes
8
The procedures for registering remote control codes
and remote control preset registration are displayed.
Category
Brand
Code [ 1/ 3]
Setup Remote
1. Press [INPUT SOURCE] button.
2. Press and hold 3sec. both [POWER ON]
[DEVICE ON] button.
3. Input Code with [0-9] button.
4. Press any key to check device.
(e.g. [DEVICE ON])
: DVD
: Denon
: 30490
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
Press QUICK 1 if device works, QUICK 2 if not
QUICK1 OK QUICK2 NG QUICK3 Return
NOTE
If a wrong brand name is selected, press QUICK SELECT 3. The
following screen is displayed:
Press [AMP] button. And press
[ENTER] button to return BRAND
SELECT MENU.
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
O K
Press AMP then ENTER to return to step 7.
9
Press the input source button on which the preset
code is to be registered (DVD, BD, SAT/CBL, DVR,
DOCK, V.AUX, GAME, CD or TV).
• For TV, only the preset code for the categories “TV”, “TV/DVD”, or
“TV/VCR” can be registered.
• For “TV”, “TV/DVD”, or “TV/VCR” categories, only the preset
code for TV can be registered.
10
Hold POWER ON and ZONE/DEVICE ON pressed
simultaneously for more than 3 seconds.
The zone mode indicator flashes twice.
11
Enter a ve-digit code using 0 – 9.
Press the buttons with an interval less than 10 seconds.
Category
Brand
Code [ 1/ 3]
Setup Remote
1. Press [INPUT SOURCE] button.
2. Press and hold 3sec. both [POWER ON]
[DEVICE ON] button.
3. Input Code with [0-9] button.
4. Press any key to check device.
(e.g. [DEVICE ON])
: DVD
: Denon
: 30490
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
Press QUICK 1 if device works, QUICK 2 if not
QUICK1 OK QUICK2 NG QUICK3 Return
• When the code is registered:
The zone mode indicator flashes twice.
• When the code is not registered correctly:
The mode indicator slowly flashes once. Perform from step 9
again.
• When an input number is not correct:
Press POWER ON once then perform the operations from step
9 again.
12
Operate the device being used to check the operation.
• If the device is operating, press QUICK SELECT 1.
Go to step 13.
• If the device is not operating, press QUICK SELECT 2.
Go to step 14.
13
The screen shown below is displayed, and registration
of the preset code is completed.
Remote Preset Codes setup is
finished.
Press [AMP] button. And press
[ENTER] button to return MENU.
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
O K
• The menu screen is retrieved. Press AMP then ENTER.
14
Either of the screens below is displayed.
q
Selected code is not matched.
Plesse try other codes.
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
• The screen is displayed for 3 seconds, then the next preset
registration screen is displayed automatically.
w
Sorry, your remote is not
supported. This function can not
be used for your device
Press [AMP] button. And press
[ENTER] button to return MENU.
MANUAL SETUP OPTION SETUP
REMOTE PRESET CODES
O K
GIf screen q is displayedH
The device may be operating with the preset code displayed next.
The preset registration screen is displayed. Repeat steps 9 to 12.
GIf screen w is displayedH
The device cannot be controlled with the remote control unit supplied
with this unit. Use the remote control unit supplied with the device
to be used. The menu screen is retrieved. Press AMP then ENTER.
Some manufacturers use more than one type of remote control code.
Preset codes to change the number and verify correct operation.
NOTE
Depending on the model and year of manufacture of your equipment,
some buttons may not operate.
To Next Page
Loading...
