EasyManuals Logo

Denon AVR-S900W User Manual

Denon AVR-S900W
266 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #209 background imageLoading...
Page #209 background image
o
Desired sound does not come out
Symptom Cause / Solution Page
The volume does not
increase.
0
The maximum volume is set too low. Set the maximum volume using “Limit” on the menu. 147
0
Appropriate volume correction processing is performed according to the input audio format and settings,
so the volume may not reach the upper limit.
No sound comes out with
the HDMI connection.
0
Check the connection of the HDMI connectors.
37
0
When outputting HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “AVR”. To output
from the TV, set “TV”.
155
0
When using the HDMI control function, check that the audio output is set to the AV amplifier on the TV. 124
No sound comes out of a
specific speaker.
0
Check that speaker cables are properly connected.
28
0
Check that a selection other than “None” is set for the “Speaker Config.” setting in menu. 179
0
Check the “Assign Mode” setting in the menu. 178
0
When the sound mode is “Stereo” and “Virtual”, audio is only output from the front speakers and
subwoofer.
No sound is produced from
subwoofer.
0
Check the subwoofer connections.
29
0
Turn on the subwoofer’s power.
0
Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.
0
When “Speaker Config.” - “Front” in the menu is set to “Large”, depending on the input signal and the
sound mode, no sound may be output from the subwoofer.
179
0
When no subwoofer audio signal (LFE) is included in the input signals, no sound may be output from the
subwoofer.
184
0
You can make the subwoofer always output sound by setting the “Subwoofer Mode” to “LFE+Main”. 184
DTS sound is not output.
0
Check that the digital audio output setting on the connected device is set to “DTS”.
0
Set “Decode Mode” on the menu to “Auto” or “DTS”.
167
Dolby TrueHD, DTS-HD,
Dolby Digital Plus audio is
not output.
0
Make HDMI connections. 42
0
Check the digital audio output setting on the connected device. On some devices, “PCM” is set by
default.
Contents Connections Playback Settings Tips Appendix
209
Front panel Display Rear panel Remote Index

Table of Contents

Other manuals for Denon AVR-S900W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-S900W and is the answer not in the manual?

Denon AVR-S900W Specifications

General IconGeneral
Channels7.2
HDMI Inputs8
HDMI Outputs2
Wi-FiYes
BluetoothYes
4K Ultra HD Pass-throughYes
Dolby AtmosYes
DTS:XNo
HDMI Pass-ThroughYes
Input Impedance47 kOhm
Input Sensitivity200 mV
THD at rated output0.08%
Signal-To-Noise Ratio98 dB
DAC Resolution24-bit / 192kHz
HDMI SwitchingYes
AirPlayYes
DLNAYes
Dimensions17.1 x 6.6 x 13.3 inches
Power Output90 W
Response Bandwidth10Hz-100kHz
Output Impedance / Channel6 Ohm
InputsHDMI
OutputsHDMI
Supported Audio FormatsMP3, WMA, AAC, FLAC, WAV
Supported Video Formats4K
Output Power / Channel90W (8 ohms, 20Hz-20kHz, 0.08% THD)

Related product manuals