Digi WI-700 - Page 20

To Next Page

To Previous Page

HI, MI, WI 700 service manual - 1 - Installation

1-13 Issue 9 04/2020

Air pipe

Feed the air pipe back out of the cabinet through cable gland and connect to the air regulator.

Ethernet cable

The Ethernet cable needs to connected to the Ethernet switch situated under the main board.

Main Page

Table of Contents3
Installation8
Shipment of Machine12
Safety13
Moving the Machine15
Programming Note16
Installation Requirements17
Installation Machine Feet18
Fitting Labeller to Labeller Arm18
Connections Inside Electrical Cabinet19
Outfeed Conveyor Connection23
Labeller Position Adjustment25
Touch Applicator Transport Packaging25
Load Cell Transit Screw26
Setting Corner Overload Stops29
Loading Labels - Signature Top Labeller31
Loading Labels - Classic Labeller35
Component Parts37
The Electrical Cabinet38
PC Main Board - Type LV-67P40
Hard Drive43
Battery44
Power Supply LS75-15-15VDC45
UPS Board45
Port Ethernet Switch47
Relay 5V48
A/D Power Supply49
A/D Unit50
Omron PLC53
Motor Driver Board56
Infeed Speed Control59
Primary Fuse60
Control Fuse60
Cooling Fans61
Software Licence Dongle61
Pack Sensors62
Outfeed Conveyor When Base Labeller Is Fitted66
Load Cell68
Touch Screen 12.170
Touch Screen `1573
Labeller - Signature74
Classic Type75
Thermal Head76
Platen Roller Option (Signature)76
Wear Strip & Silicone Tube (Signature)77
Platen Roller Option (Signature)78
Thermal Head Heaters (Signature)79
Labeller Board80
Labeller Sensor I/F Board81
Labeller Sensor I/F Board82
Power Supply 5.35V82
Power Supply 25V83
Power Supply 42V84
Stepper Motor85
Take-Up Motor86
Label Gap Sensor87
Power ON/OFF Switch88
Blow Bar90
Pneumatic Connections91
HS Blow Applicator93
Base Labeller Belt Applicator96
Air Cylinder Position on Head Assembly162
Label Gap Sensor Sensitivity Adjustment163
Take-Up Motor Torque Setting168
Multi Jet Air Box183
HS Blow Applicator Setup184
Base Labeller Belt Applicator194
Base Labeller Belt Applicator195
Labeller - Changing Thermal Head Size197
Fit Web Centralizer201
Centralization of Label Reels203
Ball Plunger Lock Tension204
Central Knob Resistance Adjustment206
Side Labelling Applicator213
End Stop Cushioning214
Air Pressure / Vacuum214
Proximity Sensor216
Software Settings216
Access to Rear of Labeller222
Labeller Height Adjustment224
Classic Labeller Servicing227
Platen Roller Change227
Thermal Head Position & Pressure232
Stepper Motor Belt Tension236
Electrical Drawings243
Electrical Cabinet244
Electrical Cabinet - Canada Specification246
Maintenance Schedule256
All Conveyors258
Scale259
Labeller260
Base Label Applicator263
Labeller Lifting Gear264
Touch Screen264
Air Regulator264
Pack Sensors264
Safety265
Outside Electrical Cabinet266
Fault Finding267
Operational Problems267
On Screen Error Messages - Console Software269
On Screen Error Messages - Worldview Software270
Labeller Problems271
Conveyors276
Pack Sensors277
Scale Not Working278
Fault Finding Checks on A/D Board278
Labeller Board Led's279
How to PING the Labeller to Check Communication280
Conveyor285
Labeller-Signature Type Labeller-Classic Type285
Finger Touch Applicator-For Signature Labeller Belt Applicator for Base Labeller Air Box Applicator-For Signature Labeller285
Finger Touch Applicator-For Classic Labeller Side Applicator - for Signature Labeller HS Blow Applicator Air Regulator285
HI-700 / HI-700W Basic Machine Specification295
MI-700 Basic Machine Specification296
WI-700 Basic Machine Specification297
HI-700 Dimensions - Single Top Labeller298
HI-700 Dimensions - Top & Base Labeller Plus Infill Conveyor after Scale300
HI-700W Dimensions301
WI-700 Dimensions304
WI-700 Dimensions305

Digi WI-700 - Page 20

Table of Contents

Related product manuals