22
SETUP MODE 2
Enter SETUP MODE 2 by opening the main door
and pushing the Service button four times. The
display will read “SETUP MODE 2”
NEXT ITEM - Press key “A”
SPACE TO SALES ENABLE/DISABLE - Press key
“B”
Allows enabling or disabling the Space-to-Sales
vend mode. When Enabled, Space-to-Sales vends
are performed according to the configurations
defined using “DEFAULT STS CONFIG” and/or
“CUSTOM STS CONFIG”.
Press the Letter “B” on the keypad. The display will
scroll the current state of the Space-to Sales vend
mode as “STS ENABLED” OR “STS DISABLED”.
There are now two choices:
1. Press the “CLR” key to leave the Space-to-
Sales vend mode unchanged and return to
“SETUP MODE 2”
2. Press the “*” key to toggle the state. The
display will scroll a new message indicating
the updated state.
CUSTOM STS CONFIG - Press key “C”
Configures the Space-to-Sales according to user
input.
Press the letter “C” on the keypad. The display will
read “START”. There are now 3 choices:
1. Pressing the “*” key will set STS to a one to
one configuration such that each selection is
mapped only to it’s corresponding column.
Note: This setting overrides any
previously defined Space-to-Sales
blocks.
2. Pressing a tray selection followed by “*” will
configure an entire tray as a single Space-
to-Sales block. Example is selections A1
through A9 vend from columns A1 through
A9 sequentially.
3. Pressing an item selection (A1) will specify
the first product of the Space-to-Sales block.
After the first item is programmed, the
display will change to “END”. Press the item
selection corresponding to the last item in
the block. This option may transcend more
than one shelf, i.e. A1 to B9.
In all of the above options, after a selection is
made, an audible tone will be heard and the
display will change briefly to “OK” then back to
“START”. Press “CLR” at any time to return to
SETUP MODE 2.
DEFAULT STS CONFIG - Press key “D”
Configures the Space-to-Sales to the preset
mappings.
Press “D” on the keypad and the display will scroll
“DEFAULT STS CONFIG”. Press the “*” key to
configure Space-to-Sales in preset blocks of three
(A1 – A3, A4-A6, A7-A9, B1-B3,…).
DISPLAY STS CONFIG - Press key “E”
Allows verification of the Space-to-Sales settings for
an individual item.
Press the letter “E” on the keypad. The display will
scroll “DISPLAY STS CONFIG”. Press the “*” key
and the display will change to “ITEM”. Enter any
selection item and the display will read “##-## ##.
The first ## indicates the first column in the
selection’s block. The second ## indicates the last
column in the selection’s block. The last ##
indicates the column that the next vend will come
from in this Space-to-Sales block. For example,
entering “A2” might display “A1-A3 A1, indicating
that selection A2 is part of the block that spans
between A1 and A3 and that A1 selection is next in
line to be vended.
SET VEND LIMIT - Press key “F”
If a Vend fails-either due to a vend error or no
product detected in the recovery unit- and the drop
sensor is enabled, the VMC will mark the column as
sold out. If the Space-to-Sales is enabled, the
product column will be removed form the Space-to-
Sales rotation and the VMC will attempt to vend from
the next column in the Space-to-Sales block. If the
vender is unable to vend any products from a
Space-to-Sales block, the customer’s credit will be
returned and the entire block will be marked as
“SOLD OUT”.
Press the “F” key on the keypad. The display will
scroll “SET VEND LIMIT”. Press the “*” key while
the display is scrolling, or wait until the message
scrolls off. The display will read” LIMIT #”. The
value # is the current vend limit which is applied to
each selection. When # is 0, no vend limits are
enforced. Enter the desired vend limit and press the
“*” key to accept this value or press the “CLR” key to
cancel changes and return to SETUP MODE 2.
To Next Page
Loading...
