dji MATRICE 200 series

II
Failsafe and Return to Home
I NOTICE)
1. The Return to Home feature will NOT work if the GPS signal is
insufficient (GPS signal less than three bars) or if GPS is not active.
2. Press the RTH (Return to Home) Button on the remote controller to
initiate the Return to Home process instead of turning off the remote
controller.
3. Tall buildings may adversely affect the Failsafe function. Please
adjust the aircraft location, altitude and speed while returning home
to avoid obstacles. Aircraft will stop ascending and immediately
return to the Home Point if you move the left stick if the aircraft
reaches 65 feet (20 meters) altitudes or beyond during Failsafe.
4. Make sure to operate the aircraft within the transmission range of
the remote controller
5. Only use the Failsafe and Return to Home functiions in case of
emergency. Such functions may be affected by the weather, the
environment, or any nearby magnetic fields.
6. The aircraft cannot avoid obstacles during the Failsafe RTH when
lighting condition is not ideal. Therefore, it is important to set an
appropriate Failsafe altitude before each flight.
7. If the battery life so allows, the aircraft may first return to the last
position where it had connection with the remote controlller during
the Failsafe RTH. As a result, you may observe the aircraft first
flying away from you, then returning to the home point.
Low Battery
I NOTICE)
When the Critical Battery Level Warning activates and the aircraft is
descending automatically, you may push the throttle up to maintain
the aiircraft's altitude and navigate it to a more appropriate location
for landing.
2. When battery warnings are triggered. promptly bring the aircraft
back to the Home Point or land to avoid losing power during flight
and causing damage to the aircraft, property, animals, and people.
D-RTK (For M210 RTK)
I NOTICE )
Only use genuine OJI parts or parts certified by OJI. Unauthorized
parts or parts from non-OJI-certificated manufacturers may cause
the system to malfunction and compromise safety.
2. Operate in an open environment free from radio interference. The
antennas should be kept at the same height and DO NOT obstruct
each other when used.
3. DO NOT bend or fold the antenna cable excessively.
4. Ensure that the D-RTK™ and its components are free from
contamination (e .. g. water, oil, soil and sand).
Vision System and Infrared Sensing System
I NOTICE )
The Vision System cannot work properly over surfaces that do NOT
have clear pattern variations. The Vision System is only effective
when the aircraft is at altitudes of 0.3 to 10 meters.
2. The Vision System may NOT function properly when the aircraft is
flying over water.
3. Keep your pets away from the aircraft when the Vision System is
activated, as the sonar sensors emit a high frequency sound that is
only audible to some pets.
4. Operate the aircraft cautiously when in any of the following
situations:
a. Flying over monochrome surfaces (e.g., pure black, pure white.
pure red, pure green).
b. Flying over highly reflective surfaces.
c. Flying at high speeds (over 14m/s at 2 meters or over 5m/s at ·1
meter).
d. Flying over water or transparent surfaces.
e. Flying over moving surfaces or objects.
f. Flying in an area where the lighting changes frequently or
drastically.
10
g. Flying over extremely dark(< 15 lux) or bright(> 10,000 lux)
surfaces.
h. Flying over surfaces that can absorb sound waves (e.g., thick
carpet).
i. Flying over surfaces without clear patterns or texture.
j. Flying over surfaces with identical repeating patterns or textures
(e.g. tiles with same design).
k. Flying over inclined surfaces that will deflect sound waves away
from the aircraft
I. Tiny obstacles (with less infrared reflection energy).
5. In the event of loss of the remote controller's signal and the GPS
signal is weak, if the aircraft cannot detect the Home Point, the
aircraft will hover fOf 8 seconds and then auto-land if it is in •p~ mode.
6. Vision System calibration is required if the aircraft suffers from
crashing. Calibrate the Vision System if the OJI GO 4 app prompts
you to do so.
7. Please be mindful of blind spots (grey) of the Vision System and
Infrared Sensing System.
/- ------'\\_\
f
1
i
1
i
\
10m
Downward viision system is only used for positioning.