DoorKing 1601 - Wiring Connections; High Voltage Terminal Connections; Dual Gate Operator Wiring

1601-065-P-12-19
8
MOVING ARM can
cause vehicle damage,
serious injury or death.
STAY CLEAR of arm
at all times.
NO: Pedestrians
Bicycles
Motorcycles
WARNING
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
MOVING ARM can
cause vehicle damage,
serious injury or death.
STAY CLEAR of arm
at all times.
NO: Pedestrians
Bicycles
Motorcycles
WARNING
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTS PHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
MOVING ARM can
cause vehicle damage,
serious injury or death.
STAY CLEAR of arm
at all times.
NO: Pedestrians
Bicycles
Motorcycles
WARNING
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
MOVING ARM can
cause vehicle damage,
serious injury or death.
STAY CLEAR of arm
at all times.
NO: Pedestrians
Bicycles
Motorcycles
WARNING
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
NC NO
UP
LOOP
DOWN
LOOP
12345678 9 10 11 12 13 14
1601
2.3 Dual Gate Operators (Primary/Secondary)
Primary/Secondary Interconnection Cable Conduit
Primary Circuit Board
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
NC NO
UP
LOOP
DOWN
LOOP
123456 7 8910 11 12 13 14
1601
Secondary Circuit Board
SW 1
SW 1, switch 4 is ON.
SW 1, switch 5 is OFF.
SW 1, switch 8 is OFF.
Set other DIP-switches
based on gate operation
preferences (See page 21).
• Set both operators DIP-switches
(SW 1 and SW 2) to the same
settings.
• Each operator requires AC power.
• Connect loop detectors and access
control devices to the PRIMARY
operator ONLY.
Yellow
Jumper Wire Jumper
Brown
Gray
Orange
Yellow
Brown
Gray
Orange
AC Power
AC Power
Access
Control
Device,
Loops
UP Loop DetectorDOWN Loop Detector
Secondary
Operator
When using Reverse Loops:
DIP-Switch settings: SW 1, switch 4 is OFF. SW 1, switch 5 is OFF. SW 1, switch 8 is OFF. Set other DIP-switches based on gate operation preferences.
Interconnection cable: The BROWN wire must be connected to SECONDARY TERMINAL #9 along with the GRAY wire. All other terminal wire connections are
the same as shown above.
Settings using
Down Loop
1
ON
2 3 4 5 6 7 8
Reverse loops
Primary/Secondary
Interconnection Cable
Sold separately from DoorKing.
4 wires used (8 - 18 AWG wires total).
Primary
Operator
Photocell mounted directly under arm for safety, see safety pages in front of manual.
Arm Note: Some of the arms need to be wired to the barrier operator.
Refer the specific arm instruction sheet to for wiring instructions.
Octagon arm shown here.
Aluminum arm shown here.