1601-065-P-12-19
10
1. Com
3. 24 Volt
2. Relay
DoorKing Access Control System (Model 1833, 1835, 1837 or
1838) tracker system can be connected.
This system can keep track of gate operator cycle count, shorted
inputs, loop detector problems, any forced entry attempts, if the
gate has struck anything during the open or close cycle, power
interruptions, etc.
For more detailed information refer to the Tracker Installation and
Wiring Manual, DoorKing P/N 2358-010.
Round Aluminum or Wood Arm Contact Sensor
See page 29
3-Wire Radio Receiver
Up-Inputs
Down-Inputs
(Photo Sensor)
Non-Contact Sensor (Always Reverses)
REVERSE
SENSITIVITY
TIME
DELAY
POWER
1
ON
2 3 4 5 6 7 8 1
ON
2 3 4 5 6 7 8
NC NO
UP
LOOP
DOWN
LOOP
1
2
3
4
567 8910 11 12 13 14
1601
Terminal 6 required only if the tracker board will activate the gate
operator. Refer to the manual 2358-065 for detailed information.
Manual Gate Control Toggle
P/N 1200-017
Up toggle position: User toggles switch up to hold gate open.
Center toggle position: Is neutral for normal operation.
User MUST make sure gate area IS CLEAR
before manually operating gate arm.
21” Typical Beam Height.
27.5” Max. Beam Height.
2.5 Control Wiring for Single/Primary Operator
OPEN
HOLD OPEN
WARNING
Contact Sensors Note: Helps minimizes the
potential of the round aluminum or wood
arm lowering on vehicular or other traffic
that loops cannot sense.
Gate Operator
Data Terminal
Coax Antenna Kit
P/N 1514-073
Antenna mounted
outside operator
housing.
Gate
Tracker
(
Quad Box
Shown)
R
E
VE
R
SE
S
EN
S
ITI
VITY
TIM
E
D
E
LA
Y
POWE
R
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
NC N
O
U
P
LOOP
D
OW
N
LOOP
Electronic
Box Assembly
115 VAC
Convenience
Outlets
Power safety and
opening devices
that require 115
VAC power.
24 VAC - 250 mA max.
Up Input
Down/Reverse Input
Reverse Input
Low Voltage Common
DANGER
HIGH VOLTAGE!
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
Terminal #5 Note:
Exceeding 250 mA of power from this terminal may cause the circuit
board transformer to overheat, causing intermittent problems.
Non-Contact Sensor Connected to Reverse Input Note: Helps
minimize the arm lowering on anything that blocks beam.
Lowering arm will always reverse when beam gets obstructed.
This setup does NOT distinguish between a vehicle and a
pedestrian. It will reverse arm for either when beam gets
obstructed. See next page for pedestrian photo sensor wiring.
Type of wiring to be used on ALL external devices:
A) Type CL2, CL2P, CL2R, or CL2X.
B) Other cable with equivalent or better electrical,
mechanical, and flammability ratings.
4-Wire 6ft Reversing Edge
P/N 8080-091
2-Wire 6ft Reversing Edge
P/N 8080-071
To Next Page
Loading...
