dosatron D3 RE 10 - Product Specifications; Technical Specifications Overview; Adjusting Injection Rate

©
DOSATRON INTERNATIONAL / 35
EN
©
DOSATRON INTERNATIONAL / 34
©
DOSATRON INTERNATIONAL / 35
SHIPPING CONTENTS: 1 DOSATRON / 1 mounting bracket for
DOSATRON / 1 suction tube of concentrated additive / 1 strainer /
1 injection suction tube for “IE” model / 1 owner's manual
PACKAGE SIZE:
55.2 x 16.5 x 14.5 cm [21 7/8" x 6 5/8" x 5 3/4"]
PACKAGE WEIGHT: 2 - 4 kg approx [~ 4.4 - 8.8 US lbs]
SPECIFICATIONS
D 3 RE 3000
D 3GL3000
D 3T
(1)
RE3000
D3RE2
D3GL2
D3T
(1)
RE2
Practical operating flow range: .......................................................................
(1)
..........................................................................
(2)
..........................................................................
Maximum operating temperature: .............................................................
(1)
..........................................................................
(2)
..........................................................................
Operating pressure:
bar
PSI
0.30 - 6
4.3 - 85
0.30 - 6
4.3 - 85
Externally adjustable or fixed injection rate:
%
Ratio
0.03 - 0.3
1:3000 - 1:333
0.2 - 2
1:500 - 1:50
Concentrated additive injection:
Mini l/h - Maxi l/h
US Fl. oz/min - MINI
US GPM - MAXI
0.003 - 9
0.0017
0.04
0.02 - 60
0.011
0.28
Connections (NPT/BSP male): ..................................................................
Hydraulic motor capacity (for every 2 clicks of the piston): .......................
NOTE: The Dosatron is not preset, see chapter
UNIT SIZE
Diameter: cm ["] 11.2 [4 7/16] 11.2 [4 7/16]
Total height: cm ["]
53 [21] 48.5 [19 3/32]
Width: cm ["] 16 [6 5/16] 16 [6 5/16]
Weight: ± kg [lbs] 1.6 [3.5] 1.7 [3.7]
D3RE5
D3GL5
D3T
(1)
RE5
D3RE10
D3GL10
D3RE25IE
(2)
....................10 l/h mini 3 m
3
/h maxi [1/3 US Pint/min - 14 US GPM]
................100 l/h mini 3 m
3
/h maxi [0.4 US Pint/min - 14 US GPM]
....................10 l/h mini 2 m
3
/h maxi [1/3 US Pint/min - 9 US GPM]
....................................................... 40 °C [104 °F]
....................................................... 60 °C [140 °F]
....................................................... 40 °C [104 °F]
0.30 - 6
4.3 - 85
0.50 - 6
7 - 85
0.50 - 4
7 - 57
0.5 - 5
1:200 - 1:2
1 - 10
1:100 - 1:10
5 - 25
1:20 - 1:4
0.05 - 150
0.028
0.7
0.1 - 300
0.056
1.4
0.5 - 500
0.2818
2.2
................................................. Ø 20x27 mm [3/4”]
........................................ about 0.53 l [0.14 US Gallons]
ADJUSTING THE INJECTING RATE
11.2 [4 7/16] 11.2 [4 7/16] 11.2 [4 7/16]
53.8 [21 3/16] 53.8 [21 3/16] 66 [26 1/8]
16 [6 5/16] 16 [6 5/16] 16 [6 5/16]
1.8 [3.9] 2 [4.4] 4 [8.8]