GS3125/GS3105 19
GG
GG
G
Options
This page is used to set the options relating to the board.
Dial options
This part is used to enter some of the characteristics relating to the telephone numbers used.
Prefix: This Device will prefix the digits entered in this field to all the telephone numbers dialled through the GSM Interface function.
If necessary enter a Prefix (maximum 8 digits) in this field. If no Prefix is required, leave this field empty.
Digits to Remove: If this Communicator is connected downstream to a switchboard, the telephone numbers (programmed on the Control
panel) must be preceded by the switchboard number (normally one digit). As the switchboard number is not required when calls are sent over
the GSM Network, it must be removed from the digits which form the telephone number. Enter the number of digits that form the switchboard
number (e.g. if switchboard number is 01, enter 2 in the “Digits to remove” field, as 2 numbers form the switchboard number).
The telephone number should at least have two digits more that the number in the “Digits to remove” area, otherwise
the engaged tone will be come through, e.g.:
— the dialled telephone number is 0123, with 2 digits to be removed = correct, the remaining number to be inserted is 23.
— the dialled telephone number is 123, with 2 digits to be removed = engaged tone, the remaining number to be
inserted is 3.
Enable Black List: Check this box if you do not wish to receive calls from telephone numbers, authorising only the numbers selected
previously using the White List function (Phonebook page->White List).
Only the “Black List” option cancels the call immediately.
When the “Black List” and “Activates Output” options are enabled, there is a delay (some seconds) before the call is
cancelled;
When the Ring is selected for the Activation Confirmation option, there is a delay (some seconds) before the call is
cancelled;
The output will be not activated when the call is canceled.
Event priority (GS3125 series only)
This page may be used to program several Communicator priorities, for the transmission of alarm events (see Priority management
section).
Off-Hook: This box can be used to establish the priority of telephone devices connected to the LI terminals (such as a burglar alarm
control panel). It is enabled
by default; to disable it remove the tick
.
Voice Dialer: This box can be used to establish Voice dialer (voice message) priority. It is disabled
by default; to enable it, mark
it with a tick
.
Codes (GS3125 series only)
User Code: Enter the account code in this box (maximum 4 numeric characters) to activate outputs remotely. For further information,
please refer to the section “Activating the Outputs->Remote Activation and Deactivation of the Outputs”: The default code
is set to ‘0001’.
Installer Code: The Installer code can be entered in this field (maximum 4 numerical characters). This code allows access to the
“Web Service” interface when required. The default code is set to ‘0002’.
Generic
This section may be used to set the audio levels of the loudspeaker and microphone fitted to the GSM transmitter.
Speaker volume: The volume of the loudspeaker may be adjusted by shifting the cursor.
Microphone volume: The volume of the microphone may be adjusted by shifting the cursor.
CAUTION: a high microphone volume may corrupt the DTFM signals, making them unrecognisable to the devices
connected to the LI terminals.
Tones...: Select the name of Communicator's country of installation: the selected country will establish a series of parameters for the
proper working of the simulated telephone call.
LE failure timeout : Enter the time in seconds (between 10 and 3600 seconds) for the Line down on the LE terminals, before the
PSTN Fault event occurs.
The time may increase up to 60 seconds if some telephone devices are connected to the terminals LI.
LE restore timeout: Enter the time in seconds (between 30 and 3600 seconds) that the telephone line must be present on the LE
terminals before the PSTN Fault event restores.
To Next Page
Loading...
Need help?
General
