Duplo DocuCutter CC-228

Other manuals for Duplo DocuCutter CC-228

Service And Parts Manual37 pages

Questions and Answers

A
Alexis Rivera MDSep 23, 2025
What to do if Duplo DocuCutter CC-228 is out of paper?
- D
  David NunezSep 23, 2025
  If your Duplo Paper Cutters indicates 'Out of paper', it means the feed tray is empty. Replenish the paper supply in the tray.
K
Kevin MeyerAug 23, 2025
Why is my Duplo Cutter miss feeding?
- A
  Amy HillAug 23, 2025
  If your Duplo Cutter is miss feeding, you should check the S1 voltage, feed motor belt, pulley screw, and motor detent torque. If there is no torque, consider replacing the driver board.
S
steven02Aug 25, 2025
What to do if there is a jam in Sensor 2 of my Duplo Cutter?
- F
  francisco95Aug 25, 2025
  If there is a jam in Sensor 2 of your Duplo Cutter, you can try the following: * Check S2. * Adjust the feed tray tension. * Adjust the ramp. * Check that the transport motor has detent torque.
D
danielbutlerAug 27, 2025
What to do if there is a jam in Sensor 3 of my Duplo Cutter?
- H
  Heather BurnsAug 27, 2025
  If there is a jam in Sensor 3 of your Duplo Cutter, you should check S3 and the detent torque of the transport motor. If there is no torque, consider replacing the driver board.
C
chloesullivanAug 27, 2025
What to do if the finish card length is uneven on my Duplo Cutter?
- M
  Michael HornAug 27, 2025
  If the finish card length is uneven on your Duplo Cutter, adjust the cutter Assy. frame mounting screw on the side plates and check the driving belt tension.
L
Leslie WilsonSep 17, 2025
What to do if jam sensor 2 on Duplo DocuCutter CC-228?
- L
  Laura LarsonSep 18, 2025
  If the Duplo Paper Cutters displays 'jam sensor 2', follow these steps: 1. Remove the paper jam by pulling toward the stacking tray. 2. If double feeding occurs, adjust the feed hopper tension.
P
prichardsSep 14, 2025
What to do if waste bin full on Duplo DocuCutter CC-228 Paper Cutters?
- W
  William CarrSep 14, 2025
  If the waste bin full error appears on your Duplo Paper Cutters, follow these steps: 1. Remove and empty the waste bin. 2. Reset the error.
J
Jennifer SanchezSep 15, 2025
How to fix miss feed on Duplo DocuCutter CC-228 Paper Cutters?
- K
  Kathleen WaltonSep 16, 2025
  If your Duplo Paper Cutters displays a 'miss feed' error, try the following: 1. Adjust the feed tray tension. 2. Adjust the side guide if it is too tight. 3. Fan the paper and reload it into the hopper.
P
Patrick JonesSep 6, 2025
What to do if my Duplo Cutter's transport has no function?
- M
  Matthew FosterSep 6, 2025
  If the transport function on your Duplo Cutter is not working, rotate the transport motor on the side frame. If there is no detent torque, replace the driver box.
A
Amber ChapmanSep 3, 2025
What to do if my Duplo Cutter displays 'Check Waste Bin'?
- A
  Allen WilsonSep 3, 2025
  If your Duplo Cutter displays 'Check Waste Bin', check the waste bin interlock switch.

Summary

Declaration of Conformity

Safety Precautions

WEEE Disposal Information

Information on the proper disposal of Waste Electrical and Electronic Equipment in Europe.

WEEE Material Information

WEEE Symbol Definitions

Defines symbols for substances, preparations, and components in WEEE.

Plastic Category Abbreviations

Lists abbreviations for plastic categories used in the parts catalogue.

Introduction and Specifications

Accessories

Lists all accessories provided with the DocuCutter CC-228 machine.

Major Components and Assemblies

Component Identification (1-7)

Identifies key components like Power Switch, Control Panel, and Feed Rollers.

Major Components and Assemblies (Part 2)

Component Identification (8-13)

Identifies additional components like Waste Bin, Stack Tray, and Slitter Module.

Control Panel Operation

Simple vs. Advance Control Panel

Details the keys and functions for both Simple and Advance control panels.

Key Functions Explanation

Explains the purpose of each key on the control panels.

Machine Installation

Waste Bin and Stack Tray Installation

Guides on inserting the waste bin and attaching the stacking tray.

Power Cord and Control Panel Setup

Instructions for connecting the power cord and applying the control panel sticker.

Setting Up Procedure

Paper Width Adjustment

Details how to adjust the paper width using the thumbscrew knob.

Paper Loading and Tray Pressure

Explains paper preparation, loading, and adjusting tray pressure for different paper weights.

Predefined Job Selection

Job Details and Layouts

Presents 5 predefined jobs with descriptions, finished sizes, and layouts.

Job Layout Diagrams

Job 1-3 Layouts

Illustrates the layout for business card and 3.5x5 card jobs.

Job 4-5 Layouts

Shows layouts for 8x4 and 7x5 card jobs, noting optional slitters.

Job and Batch Count Operation

Selecting a Job

Step-by-step guide on how to select a job using the control panel.

Batch Count Function

Explains how to use the batch count to automatically stop the machine.

User Defined Job Programming

Entering Program Mode

How to enter program mode for user-defined jobs.

Customizing Job Settings

Steps to adjust finished length, top margin, and gutter length.

Operational Functions

Cut Mark Functionality

Explains the purpose and activation of the cut mark feature.

Turbo Mode and Waste Bin

Details on using Turbo Mode and handling a full waste bin.

Counter Reset and Jam Clearing

Instructions for resetting the counter and clearing paper jams.

Error Message and Troubleshooting

Troubleshooting Common Errors

Provides solutions for common error messages like 'Out of paper' and 'miss feed'.

Cover and Bin Error Resolution

Troubleshooting steps for cover, waste bin, and reset errors.