Dynapac SD2550C - Page 468

468 pages

Save Page as PDF

To Previous Page

To Previous Page

Loading...

www.atlascopco.com

Table of Contents

Table of contents3
V Preface13
- 1 General safety instructions14
- 2 CE identification and Declaration of Conformity22
- 3 Guarantee conditions22
- 4 Residual risks23
- 5 Sensibly predictable incorrect usage24
A Correct use and application25
B Vehicle description27
- 1 Application27
- 2 Description of assemblies and functions28
  - 2.1 Vehicle29
    - Construction29
- 3 Danger zones33
- 4 Safety devices34
- 5 Technical data, standard configuration36
- 6 Location of instruction labels and identification plates44
- 7 EN standards58
C 11 Transportation61
- 1 Safety regulations for transportation61
- 2 Transportation on low-bed trailers62
  - 2.1 Preparations62
- 3 Securing the load64
- 4 Securing the load69
- 5 Control panel transport safeguard:72
  - 5.1 After transportation73
    - Protective roof (o)74
- 6 Transportation76
  - 6.1 Preparations76
  - 6.2 Driving mode78
- 7 Loading by crane79
- 8 Towing82
- 9 Safely parking the vehicle84
  - 9.1 Lifting the vehicle with hydraulic lifts, lifting points85
D 11 Operation87
- 1 Safety regulations87
- 2 Controls89
  - 2.1 Operating panel89
  - 2.2 Special functions136
    - Reversible conveyor136
- 3 Remote control139
D 21 Operation157
- 1 Operation of the input and display terminal157
- 2 Terminal error messages181
  - 2.1 Drive engine error codes182
  - 2.2 Error codes184
- 3 Menu structure of the setting and display menus191
D 30 Operation193
- 1 Operating elements on the paver finisher193
  - 1.1 Control elements on the operator's control station193
D 41 Operation237
- 1 Preparing for operation237
- 2 Malfunctions274
  - 2.1 Problems during paving274
  - 2.2 Malfunctions on the paver finisher or screed276
E 11 Set-up and modification279
- 1 Special notes on safety279
- 2 Distribution auger280
- 3 Auger extension284
- 4 Offsetting the screed310
- 5 Levelling311
- 6 Automatic steering unit326
  - 6.1 Mounting the automatic steering unit on the paver finisher327
- 7 Emergency stop during feeder operation330
- 8 Limit switch331
  - 8.1 Auger limit switches (left and right) - mounting the PLC version331
- 9 Special accessories332
  - 9.1 Material bucket332
- 10 Identification points337
- 11 Screed352
- 12 Electrical connections352
  - 12.1 Machine operation without remote control / side board353
F 10 Maintenance355
- 1 Notes regarding safety355
F 26 Maintenance review357
- 1 Maintenance review357
F 31 Maintenance - conveyor359
- 1 Maintenance - conveyor359
  - 1.1 Maintenance intervals361
  - 1.2 Points of maintenance362
F 40 Maintenance - auger assembly367
- 1 Maintenance - auger assembly367
  - 1.1 Maintenance intervals369
  - 1.2 Points of maintenance371
F 52 Maintenance - engine assembly Tier 4i (o)379
- 1 Maintenance - engine assembly379
  - 1.1 Maintenance intervals381
  - 1.2 Points of maintenance384
F 60 Maintenance - hydraulic system397
- 1 Maintenance - hydraulic system397
  - 1.1 Maintenance intervals399
  - 1.2 Points of maintenance401
F 74 Maintenance – drive units413
- 1 Maintenance – drive units413
  - 1.1 Maintenance intervals415
  - 1.2 Points of maintenance418
F 81 Maintenance - electrical system427
- 1 Maintenance - electrical system427
  - 1.1 Maintenance intervals429
  - 1.2 Points of maintenance430
F 90 Maintenance - lubricating points441
- 1 Maintenance - lubricating points441
  - 1.1 Maintenance intervals442
  - 1.2 Points of maintenance443
    - Central lubrication system (1)443
    - Bearing points (2)447
F 100 Tests, stopping ...449
- 1 Tests, checks, cleaning, stopping449
  - 1.1 Maintenance intervals450
- 2 General visual inspection451
- 3 Check that the bolts and nuts fit firmly451
- 4 Inspection by an expert452
- 5 Cleaning453
  - 5.1 Cleaning the hopper454
  - 5.2 Cleaning the conveyor and auger454
- 6 Preserving the paver finisher455
- 7 Environmental protection, disposal456
  - 7.1 Environmental protection456
  - 7.2 Disposal456
- 8 Bolts - torques457
  - 8.1 Standard metric threads - strength class 8.8 / 10.9 / 12.9457
  - 8.2 Fine metric threads - strength class 8.8 / 10.9 / 12.9458
F 112 Lubricants and operating substances459
- 1 Lubricants and operating substances459
  - 1.1 Capacities461
- 2 Operating substance specifications462

Related product manuals

Preview: Dynapac SD2500C

Dynapac SD2500C

Preview: Dynapac SD2500W

Dynapac SD2500W

Preview: Dynapac Svedala Demag DF 115 P/D

Dynapac Svedala Demag DF 115 P/D

Preview: Dynapac LH700

Preview: Dynapac CA 602

Preview: Dynapac CA150D

Preview: Dynapac CA 250

Preview: Dynapac CC1300C

Dynapac CC1300C

Preview: Dynapac CA 262 Series

Dynapac CA 262 Series