www.eaton.com Page 4-11
MP-4000 IB02602002E
Table 4-3. View Setting Mode/Program Worksheet.
SUB-
MENU
LINE # DISPLAY HELP MESSAGE SETTING RANGE/VALUE
(DEFAULT SELECTION AND
VALUE AS SHIPPED IN BOLD)
VALUE SELECTED
PAGE 9, SP AUX 1 SETTINGS FOR AUX 1 RELAY OUTPUT CONFIGURATION
1 LSPU XXX LOAD SHED PICK-UP CURRENT AS
% OF FLA
50-150%, OFF (1% increments)
NOTE: P9L1 and P9L2 are forced to be
coherent. Refer to Section 5 for details.
2 LSDO XXX LOAD SHED DROP-OUT CURRENT AS
% OF FLA
50-LSPU Value %, OFF (1% increments)
NOTE: P9L1 and P9L2 are forced to be
coherent. Refer to Section 5 for details.
3 LSDL XX LOAD SHED DELAY IN SECONDS 0-5 sec. (0.1 sec. Increments)
If LSPU and LSDO are both set to OFF, the
SP AUX1 functions below are available and
visible. (1)
4 Choose:
GF A ON
GFT ON
or
GF OFF
ENABLE GROUND FAULT ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between GF A ON, GF T ON, and
GF OFF
5 Choose:
I2T A ON
I2T T ON
or
I2T OFF
ENABLE I2T ALARM OR TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between I2T A ON, I2T T ON, and
I2T OFF
6 Choose:
JAM A ON
JAM T ON
or
JAM OFF
ENABLE JAM ALARM OR TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between JAM A ON, JAM T ON, and
JAM OFF
7 Choose:
UL A ON
UL T ON
or
UL OFF
ENABLE UNDERLOAD ALARM OR TRIP
TO ACTIVATE AUX1 RELAY OUTPUT
OR DISABLE
Toggles between UL A ON, UL T ON, and UL
OFF
8 Choose:
UB A ON
UB T ON
or
UB OFF
ENABLE PHASE UNBALANCE ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between UB A ON, UB T ON, and
UB OFF
9 Choose:
WD A ON
WD T ON
or
WD OFF
ENABLE WINDING TEMP ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between WD A ON, WD T ON, and
WD OFF
10 Choose:
MB A ON
MB T ON
or
MB OFF
ENABLE MOTOR BEARING ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between MB A ON, MB T ON, and
MB OFF
11 Choose:
LB A ON
LB T ON
or
LB OFF
ENABLE LOAD BEARING ALARM OR
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between LB A ON, LB T ON, and
LB OFF
12 Choose:
AX A ON
AX T ON
or
AX OFF
ENABLE AUXILIARY RTD TEMP ALARM
OR TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between AX A ON, AX T ON, and
AX OFF
13 Choose:
SX A ON
SX T ON
or
SX OFF
ENABLE STARTS PER TIME TRIP OR
ALARM TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between SX A ON, SX T ON, and
SX OFF
14 Choose:
TBS T ON
or
TBS OFF
ENABLE TIME BETWEEN STARTS TRIP
TO ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between TBS T ON and TBS OFF
15 RTDF ON
or
RTDF OFF
ENABLE INDIVIDUAL RTD CHANNEL
FAILURE TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between RTDF ON and RTDF OFF
To Next Page
Loading...
