Eaton MP-4000 - Page 26

Page 4-12
www.eaton.com
IB02602002E MP-4000
Table 4-3. View Setting Mode/Program Worksheet.
SUB-
MENU
LINE # DISPLAY HELP MESSAGE SETTING RANGE/VALUE
(DEFAULT SELECTION AND
VALUE AS SHIPPED IN BOLD)
VALUE SELECTED
16 RCOM ON
or
RCOM OFF
ENABLE RTD MODULE
COMMUNICATION FAILURE TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between RCOM ON and RCOM OFF
17 IOCT ON
or
IOCT OFF
ENABLE INSTANTANEOUS TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between IOCT ON and IOCT OFF
18 PH R ON
or
PH R OFF
ENABLE PHASE REVERSAL TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between PH R ON and PH R OFF
19 INSQ ON
or
INSQ OFF
ENABLE INCOMPLETE SEQUENCE
TRIP TO ACTIVATE AUX1 RELAY
OUTPUT OR DISABLE
Toggles between INSQ ON and INSQ OFF
20 REMT ON
or
REMT OFF
ENABLE REMOTE TRIP TO ACTIVATE
AUX1 RELAY OUTPUT OR DISABLE
Toggles between REMT ON and REMT OFF
21 DIFT ON
or
DIFT OFF
ENABLE DIFFERENTIAL TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between DIFT ON and DIFT OFF
22 INCT ON
or
INCT OFF
ENABLE INCOM TRIP TO ACTIVATE
AUX1 RELAY OUTPUT OR DISABLE
Toggles between INCT ON and INCT OFF
23 TRNT ON
or
TRNT OFF
ENABLE TRANSITION TRIP TO
ACTIVATE AUX1 RELAY OUTPUT OR
DISABLE
Toggles between TRNT ON and TRNT OFF
24 ZSWT ON
or
ZSWT OFF
ENABLE ZERO SPEED SWITCH TRIP
TO ACTIVATE AUX1 RELAY OUTPUT
OR DISABLE
Toggles between ZSWT ON and ZSWT OFF
25 TBYP ON
or
TBYP OFF
ENABLE TRIP BYPASS TO ACTIVATE
AUX1 RELAY OUTPUT OR DISABLE
Toggles between TBYP ON and TBYP OFF
PAGE 10, SP AUX2 SETTINGS FOR AUX 2 RELAY OUTPUT CONFIGURATION
1 TRN ON
or
TRN OFF
ENABLE TRANSITION OUTPUT IF
ENABLED ALL OTHER FUNCTIONS
FOR AUX 2 ARE DISABLED
Toggles between TRN ON and TRN OFF.
If TRN is set to OFF, then the following SP AUX2
functions are available and visible.
2 Choose:
GF A ON
GF T ON
or
GF OFF
ENABLE GROUND FAULT ALARM OR
TRIP TO ACTIVATE AUX 2 RELAY
OUTPUT OR DISABLE
Toggles between GF A ON, GF T ON, and
GF OFF
3 Choose:
I2T A ON
I2T T ON
or
V
ENABLE I2T ALARM OR TRIP TO
ACTIVATE AUX2 RELAY OUTPUT OR
DISABLE
Toggles between I2T A ON, I2T T ON, and
I2T OFF
4 Choose:
JAM A ON
JAM T ON
or
JAM OFF
ENABLE JAM ALARM OR TRIP TO
ACTIVATE AUX2 RELAY OUTPUT OR
DISABLE
Toggles between JAM A ON, JAM T ON, and
JAM OFF
5 Choose:
UL A ON
UL T ON
or
UL OFF
ENABLE UNDERLOAD ALARM OR TRIP
TO ACTIVATE AUX2 RELAY OUTPUT
OR DISABLE
Toggles between UL A ON, UL T ON, and
UL OFF
6 Choose:
UB A ON
UB T ON
or
UB OFF
ENABLE PHASE UNBALANCE ALARM
OR TRIP TO ACTIVATE AUX2 RELAY
OUTPUT OR DISABLE
Toggles between UB A ON, UB T ON, and
UB OFF
7 Choose:
WD A ON
WD T ON
or
WD OFF
ENABLE WINDING TEMP ALARM OR
TRIP TO ACTIVATE AUX2 RELAY
OUTPUT OR DISABLE
Toggles between WD A ON, WD T ON, and
WD OFF