What does error text: 11 calibration mean for my ELTEX KNH35 Portable Generator?
The error text '11 calibration' indicates defective or missing calibration data in the EEPROM. This signifies a memory problem, and the unit should be sent for repairs.
What to do if my ELTEX KNH35 displays error text: 04 short-circuit?
If your ELTEX Portable Generator displays the error text '04 short-circuit', it indicates a short-circuit has been detected. To resolve this, disconnect the connected consumers one after the other to identify and isolate the short-circuit.
What does error text 30 temperature rise mean for my ELTEX Portable Generator and how to fix it?
Error text 30 'temperature rise' indicates that the internal temperature of your ELTEX Portable Generator is too high. Here's what you can do: * Check the maximum permissible temperature and reduce the generator load if necessary. * Verify the installation position, as heat loss is best when the generator is mounted in a hanging position. * Ensure adequate air circulation if the generator is inside a cabinet.
What to do if my ELTEX Portable Generator displays error text: 02 spark counter 1?
If your ELTEX Portable Generator displays the error text '02 spark counter 1', it means there were 5 high-power discharges within a short period. To fix this, reduce the output voltage and clean the bars as described in the Maintenance section.
What does error text: 16 mains voltage mean on my ELTEX Portable Generator?
The error text '16 mains voltage' on your ELTEX Portable Generator indicates that the generator, operating with 115 V mains voltage, has detected a non-permissible mains voltage. Acknowledge the error by switching the generator off and then back on. If the error reappears, inspect the supply network for voltage peaks and contact Eltex if needed.
What does error text: 03 spark counter 2 mean on my ELTEX Portable Generator?
The error text '03 spark counter 2' indicates that the processor measuring range was exceeded. To resolve this, reduce the output voltage, clean the bars (see Maintenance), and check the high voltage cables.
What does error text: 105 release analog mean for my ELTEX KNH35?
The error text '105 release analog' means that before activating the release source analog setpoint, the parameter ext. setpoint must be set to .
What does error text: 106 release setpoint mean for my ELTEX KNH35 Portable Generator?
The error text '106 release setpoint' means that before deactivating the ext. setpoint, the release source ext. setpoint must be deactivated.
What does error text: 33 service data mean for my ELTEX KNH35?
The error text '33 service data' indicates an error in the service data. Acknowledge the error. If it recurs, it indicates a memory problem, and the unit should be sent for repairs.
What does error text: 31 watchdog mean on ELTEX Portable Generator?
The error text '31 watchdog' indicates an error in the electronics of your ELTEX Portable Generator. Switch the appliance off and back on. If the error persists, contact Eltex Service.
Explains warning and caution symbols used in the manual to identify potential dangers.
Addresses requirements for contact protection against live components as per regulations.
Manufacturer's right to modify specifications and provide updated information upon request.
Defines approved applications, warranty limitations, and prohibitions on modifications.
Detailed safety instructions for maintenance, repairs, and general operation to prevent hazards.
Instructions for mounting the generator unit, ensuring proper air circulation and access.
Details on establishing a permanent and correct ground connection for safety and proper operation.
Guidelines for routing high voltage cables, including bending radius, spacing, and bore diameter calculations.
Lists compatible charging bar models and considerations for using distributor boxes.
Step-by-step method for connecting high voltage cables, emphasizing safety precautions.
Procedure for safely disconnecting high voltage cables, including necessary precautions.
Instructions for connecting the mains power supply to the generator.
Details on integrating the generator with external systems via the analog interface.
Procedure for properly laying and connecting the cable shield for interface cables.
Procedure for safely switching on the high voltage generator and initial operation.
Explanation of the menu system, operator key functions, and navigation.
Details on available functions, setting options, and default factory configurations.
Guidance on adjusting the desired output voltage or current setpoint.
Instructions for accessing and modifying operating parameters, including password entry.
Configuration options for output-specific parameters like operating mode, limits, and ramp times.
Settings that affect the entire generator, such as language and default configurations.
Accessing diagnostic information and system parameters within the service menu.
Instructions for checking the generator's proper functioning and fuse access.
Cleaning procedures for charging bars using compressed air and cleaning gasoline.
Step-by-step guide for assembling plug connectors for the analog interface.
General| Brand | ELTEX |
|---|---|
| Model | KNH35 |
| Category | Portable Generator |
| Language | English |
To Next Page
