Emerson Dixell iChill IC207D - Page 152

1592015610 User manual IC200D EVO GB rel1.0 10.11.2015_rev10 IC200D 152/192
CO 16
Operative mode of the evaporator pump / supply fan (See Evaporator pump
function)
0= Not enabled (evaporator pump or supply fan).
1= Continuous. When the unit is running in Chiller or HP the pump or the
supply fan is running.
2= With compressor. When a compressor is running also the pump or the
supply fan is running.
0
2
CO 17
ON compressor delay after water pump / supply fan start-up (See water pump
functioning).
1
250
sec
10sec
CO 18
OFF delay evaporator water pump / supply fan after compressor switching
OFF. This delay is also active when the unit is turned in stand-by (See
evaporator water pump function).
0
250
Min
CO 19
Number of time running hours for pump rotation (See water pump group
function)
0
999
10Hr
10Hr
CO 20
Time to make run the pumps together before rotating from one to the other
(See water pump group function)
0
250
Sec
CO 21
Operative mode for condenser water pump (See condenser water pump
function)
0= Not enabled.
1= Continuous. When the unit is running in Chiller or HP the is running.
2= With compressor. When a compressor is running also the pump is running.
0
2
CO 22
Free
CO 23
OFF delay condenser water pump after compressor switching OFF. This
delay is also active when the unit is turned in stand-by (See evaporator water
pump function).
0
250
Min
CO 24
Number of time running hours for pump rotation (See water pump group
function).
0
999
10Hr
10Hr
CO 25
Time to make run the pumps together before rotating from one to the other
(See water pump group function).
0
250
Sec
CO 26
Compressor 1 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 27
Compressor 2 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 28
Compressor 3 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 29
Compressor 4 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 30
Compressor 5 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 31
Compressor 6 operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 32
“Evaporator pump / Supply fan” operation time to generate maintenance
warning
0
999
10 Hr
10 Hr
CO 33
2nd Evaporator pump operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 34
Condenser pump operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 35
2nd Condenser pump operation time to generate maintenance warning
0
999
10 Hr
10 Hr
CO 36
Pump down operating mode (See pump down ON/OFF function)
0= Not enabled
1= Unit off with pump–down, unit on without pump–down
2= Unit off with pump–down, unit on with pump–down
3= Chiller mode off with pump–down, chiller mode on without pump–down
4= Chiller mode off with pump–down, chiller mode on with pump–down
0
4
CO 37
Pump–down pressure setpoint (See pump down ON/OFF function)
0.0
0
50.0
725
Bar
psi
Dec
int
CO 38
Pump-down pressure differential (See pump down ON/OFF function)
0.1
1
12.0
174
Bar
psi
Dec
int
CO 39
Maximum pump–down time duration at start-up and stop (See pump down
ON/OFF function)
0
250
Sec
CO 40
Unloading compressor setpoint in chiller. From high temperature of the
evaporator water inlet (See unloading function).
-50.0
-58
110.0
230
°C
°F
Dec
int
CO 41
Unloading Differential. From high temperature of the evaporator water inlet
(See unloading function).
0.1
0
25.0
45
°C
°F
Dec
int
CO 42
Delay time to engage the Unloading function from high temperature of the
evaporator water inlet (See unloading function).
1
250
10 Sec
10 sec
CO 43
Maximum unloading duration time to keep activated the Unloading function
from high temperature of the evaporator water inlet (See unloading function).
0
250
Min
CO 44
Unloading compressor setpoint. From temperature / pressure in chiller mode
(See unloading function).
-50.0
-58
0.0
0
110.0
230
50.0
725
°C
°F
Bar
Psi
Dec
int
Dec
int
CO 45
Unloading Differential. From temperature / pressure in chiller mode (See
unloading function).
0.1
0
0.1
1
25.0
45
14.0
203
°C
°F
Bar
Psi
Dec
int
Dec
int
CO 46
Unloading compressor setpoint. From temperature / pressure in HP mode
(See unloading function).
-50.0
-58
0.0
0
110.0
230
50.0
725
°C
°F
Bar
Psi
Dec
int
Dec
int