S600 Instruction Manual
Index
A E
Accept................................................................ 5-4 Enter .................................................................. 5-3
Alarm ................................................................. 5-4 Entering Data ..................................................... 5-8
Alarm LED ......................................................... 5-4 Environmental Considerations........................... 2-2
Alarm Log ........................................................ 5-12 Ethernet LAN Port.............................................. 3-7
All Alarms......................................................... 5-12 Ethernet Port.................................................... 3-10
American.......................................................... 4-13 Event Log......................................................... 5-12
Analog Outputs (DAC)....................................... 4-5 Exponent............................................................ 5-3
Analogue Inputs (ANIN)..................................... 4-3 Exponential Format.......................................... 5-11
Archived Reports ............................................. 5-12
Arrow key........................................................... 5-3
F
F Keys................................................................ 5-2
B
Figures
1-1. The FloBoss S600 Flow Manager.......... 1-2 Backup
1-2. CPU Board ............................................. 1-3 Battery ........................................................... 3-4
1-3. Intelligent I/O Board ............................... 1-4 Battery Backup .................................................. 3-4
2- 1. FloBoss S600 System........................... 2-2 BIOS
2- 2. Removing the Front Panel .................... 2-3 Upgrading...................................................... 8-8
2- 3. Lifted Front Panel.................................. 2-4 Bit Links ............................................................. 3-9
2- 4. Remove Connector ............................... 2-4 I/O Board ..................................................... 4-14
2- 5. Panel Mount Dimensions ...................... 2-5 Prover Board ............................................... 4-24
2- 6. Panel Cutout Dimensions...................... 2-6
2- 7. Panel Mount Support ............................ 2-6
C
2- 8. Unscrewing the Retention Screws ........ 2-8
Change .............................................................. 5-3
2- 9. Using the Ejectors ................................. 2-8
Changing the Fuse ............................................ 8-6
2-10. Board Ready for Removal or Insertion. 2-9
Clear .................................................................. 5-3
3-1. P152 CPU Backplate ............................. 3-2
Clear SRAM....................................................... 8-5
3-1. P152 CPU Board.................................... 3-2
Cold Start........................................................... 7-1
3-3. P152 CPU Terminations ........................ 3-3
COM1 ................................................................ 3-7
3-4. Pin Connections ..................................... 3-6
COM2 ................................................................ 3-7
3-5. Link Cable .............................................. 3-8
Communications ................................................ 3-5
3-6. Dual Ethernet Communications Card .. 3-11
Config Report................................................... 5-12
4- 1. Backplate with P144 I/O Board ............. 4-2
Config Transfer .................................................. 1-5
4- 2. P144 I/O Board...................................... 4-2
Constants Log.................................................. 5-12
4- 3. P144 I/O Board Terminations................ 4-3
CPU Board......................................................... 3-1
4- 4. Analogue Input Schematic (with IS barrier
and Internal Resistor ................................... 4-4
CPU On-board Connectors ............................... 3-9
Current Alarms................................................. 5-12
4- 5. Analogue Input Schematic (without IS
Barrier and External Resistor)..................... 4-4
Current Report ................................................. 5-12
4- 6. Analogue Output Schematic (S600-
Powered) ..................................................... 4-5
D
4- 7. Analogue Output Schematic (Externally
Powered Device) ......................................... 4-6
Data
Entering ......................................................... 5-8
4- 8. Analogue Output Schematic (Externally
Powered through S600) .............................. 4-6
Data display ....................................................... 5-5
Default display ................................................. 5-10
4- 9. Digital Input Schematic (Open Collector
Device) ........................................................ 4-7
Digital Inputs (DIGIN)................................ 4-6, 4-18
Digital Outputs
4-10. Digital Input Schematic (Relay)............ 4-7
DIGOUT................................................ 4-8, 4-20
4-11. Digital Output Schematic (Relay) ......... 4-8
DIN................................................................... 4-13
4-12. Digital Output Schematic (24 V Switched
Indicator) ..................................................... 4-8
Display ............................................................... 5-3
LCD ............................................................... 5-5
4-13. Pulse Input Schematic (with EU-12 V
P148 Mezzanine Card)................................ 4-9
Navigating ..................................................... 5-7
Display Dump .................................................. 5-12
4-14. Pulse Input Schematic (with US 24 V
P148 Mezzanine Card).............................. 4-10
Display Shortcut............................................... 5-10
Dual Ethernet................................................... 3-10
Revised Jan-07 Index I-1
To Next Page
Loading...
Need help?
General