What does error code F164 mean on Endress+Hauser Deltabar FMD71 and how can I fix it?
The error code F164 on your Endress+Hauser Measuring Instruments indicates that the sensor modules cannot be synchronized or that there are electromagnetic effects outside the permitted range, or defective sensor module(s). To fix this, try restarting the device or replacing the sensor module.
What to do if Endress+Hauser Measuring Instruments shows error F163?
If your Endress+Hauser Measuring Instruments shows error code F163, it may be due to an interrupted cable connection between sensor modules HP and LP, a defective sensor module (slave), or electromagnetic effects outside the permitted range. Try restarting the device or checking the sensor module cable.
What does error code F083 mean on Endress+Hauser Measuring Instruments and what are possible solutions?
The error code F083 on your Endress+Hauser Measuring Instruments can occur due to electromagnetic effects outside the permitted range or a defective sensor module. You can try restarting the device.
What does error code F162 mean on Endress+Hauser Measuring Instruments and how to fix it?
The error code F162 on your Endress+Hauser Measuring Instruments may indicate a defective sensor module (master) or electromagnetic effects outside the permitted range. To address this, check the sensor cable and replace the sensor.
What does error code F282 mean on Endress+Hauser Deltabar FMD71 and how to resolve it?
The error code F282 on your Endress+Hauser Measuring Instruments indicates a fault in the main electronics. To resolve this, try replacing the electronics or restarting the device.
What does error code F081 mean on Endress+Hauser Measuring Instruments and how to troubleshoot it?
Error code F081 on Endress+Hauser Measuring Instruments can be triggered by electromagnetic effects exceeding specifications, a defective sensor module, or a disconnected cable between the sensor module and main electronics. To resolve this, check the sensor cable or perform a reset.
What does error code F062 mean on Endress+Hauser Deltabar FMD71 and how can I resolve it?
The error code F062 on your Endress+Hauser Measuring Instruments can be caused by several factors, including electromagnetic effects exceeding specifications, a defective sensor module, or a disconnected cable between the sensor module and main electronics. You can try replacing the electronics or checking the sensor module cable.
What does error code F261 mean on Endress+Hauser Deltabar FMD71 Measuring Instruments and how to fix it?
The error code F261 on your Endress+Hauser Measuring Instruments indicates a fault related to the main electronics or the sensor module. To address this issue, try restarting the device or replacing the electronics.
How to fix HART communication not working on Endress+Hauser Measuring Instruments?
If HART communication is not working on your Endress+Hauser Measuring Instruments, it could be due to a few reasons. First, check if the communication resistor (250 ?) is missing or incorrectly installed, and install it correctly. Also, verify that the Commubox is properly connected and set the Commubox selector switch to "HART".
What to do if Endress+Hauser Measuring Instruments device measures incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, the most likely cause is a configuration error. To fix this, check and correct the parameter configuration.
General| Device Type | Differential Pressure Transmitter |
|---|---|
| Measuring Principle | Piezoresistive |
| Output Signal | 4 to 20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 45 V DC |
| Accuracy | ±0.065% of span |
| Process Temperature | -40 to 150°C (-40 to 302°F) |
| Ambient Temperature | -40 to 85°C (-40 to 185°F) |
| Process Connection | Thread, flange, hygienic connections |
| Housing Material | Aluminum |
| Diaphragm Material | 316L Stainless Steel |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Approvals | ATEX, IECEx |
| Protection Class | IP67 |
| Process Pressure (Absolute) | Up to 40 bar |
| Application | Level, flow, and differential pressure measurement in liquids, gases, and vapors |
To Next Page