What does error code F282 mean on Endress+Hauser Deltabar FMD71 and how to resolve it?
The error code F282 on your Endress+Hauser Measuring Instruments indicates a fault in the main electronics. To resolve this, try replacing the electronics or restarting the device.
What does error code F162 mean on Endress+Hauser Measuring Instruments and how to fix it?
The error code F162 on your Endress+Hauser Measuring Instruments may indicate a defective sensor module (master) or electromagnetic effects outside the permitted range. To address this, check the sensor cable and replace the sensor.
What does error code F083 mean on Endress+Hauser Measuring Instruments and what are possible solutions?
The error code F083 on your Endress+Hauser Measuring Instruments can occur due to electromagnetic effects outside the permitted range or a defective sensor module. You can try restarting the device.
What to do if Endress+Hauser Measuring Instruments shows error F163?
If your Endress+Hauser Measuring Instruments shows error code F163, it may be due to an interrupted cable connection between sensor modules HP and LP, a defective sensor module (slave), or electromagnetic effects outside the permitted range. Try restarting the device or checking the sensor module cable.
What does error code F164 mean on Endress+Hauser Deltabar FMD71 and how can I fix it?
The error code F164 on your Endress+Hauser Measuring Instruments indicates that the sensor modules cannot be synchronized or that there are electromagnetic effects outside the permitted range, or defective sensor module(s). To fix this, try restarting the device or replacing the sensor module.
What to do if Endress+Hauser Measuring Instruments device is not responding?
If your Endress+Hauser Measuring Instruments device isn't responding, there are a few things you can check: * First, ensure that the supply voltage matches what's specified on the device's nameplate and apply the correct voltage. * Next, verify that the supply voltage has the correct polarity; if it doesn't, reverse the polarity. * Finally, check the connection of the cables to the terminals, and correct them if necessary.
What does error code F283 mean on Endress+Hauser Measuring Instruments and how can it be fixed?
The error code F283 on your Endress+Hauser Measuring Instruments may be caused by defective main electronics, electromagnetic effects exceeding specifications, the supply voltage being disconnected during writing, or an error occurring during writing. You can try performing a reset or replacing the electronics.
What does error code F411 mean on Endress+Hauser Deltabar FMD71 and how can I resolve it?
The error code F411 on your Endress+Hauser Measuring Instruments indicates that the file is defective or that data are not being correctly transmitted during the download due to issues like open cable connections, spikes on the supply voltage, or electromagnetic effects. Try repeating the download, using another file, or performing a reset.
What does error code F165 mean on Endress+Hauser Measuring Instruments?
The error code F165 on your Endress+Hauser Measuring Instruments indicates that the assignment of the transmitter to sensor module LP or HP is unknown. To resolve this, connect the transmitter set, restart the device.
What does error code M283 mean on Endress+Hauser Measuring Instruments and how to fix it?
The error code M283 on your Endress+Hauser Measuring Instruments has the same cause as F283. A correct measurement can continue as long as you do not need the peakhold indicator function. You can try performing a reset or replacing the electronics.
General| Device Type | Differential Pressure Transmitter |
|---|---|
| Measuring Principle | Piezoresistive |
| Output Signal | 4 to 20 mA HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Power Supply | 10.5 to 45 V DC |
| Accuracy | ±0.065% of span |
| Process Temperature | -40 to 150°C (-40 to 302°F) |
| Ambient Temperature | -40 to 85°C (-40 to 185°F) |
| Process Connection | Thread, flange, hygienic connections |
| Housing Material | Aluminum |
| Diaphragm Material | 316L Stainless Steel |
| Communication | HART, PROFIBUS PA, FOUNDATION Fieldbus |
| Approvals | ATEX, IECEx |
| Protection Class | IP67 |
| Process Pressure (Absolute) | Up to 40 bar |
| Application | Level, flow, and differential pressure measurement in liquids, gases, and vapors |
To Next Page