Endress+Hauser HART Micropilot S FMR533 - Page 7

Micropilot S FMR533 4 to 20 mA HART Identification
Endress+Hauser 7
2.1.2 Ordering structure
10 Approval:
A Non-hazardous area
1 ATEX II 1/2G EEx ia IIC T6 - XA Note safety instruction (electrostatic charging)!
6 ATEX II 1/2G EEx ia IIC T6, WHG - XA Note safety instruction (electrostatic charging)!
D IEC Ex ia IIC T6 (in preparation)
G ATEX II 3G EEx nA II T6
I NEPSI Ex ia IIC T6 (in preparation)
S FM IS Cl.I Div.1 Gr. A-D, zone 0,1,2
U CSA IS Cl.I Div.1 Gr. A-D, zone 0,1,2
K TIIS Ex ia IIC T3
L TIIS Ex ia IIC T6
Y Special version, TSP-No. to be spec.
20 Antenna:
A 450mm/20", Parabolic,no wetted O-ring
Y Special version, TSP-No. to be spec.
30 Process connection:
-- EN-Flanges --
CWJ DN150 PN10/16 B1, 316L flange EN1092-1 (DIN2527 C)
CXJ DN200 PN16 B1, 316L flange EN1092-1 (DIN2527 C)
C6J DN250 PN16 B1, 316L
-- ANSI-Flanges --
AVJ 6" 150lbs RF, 316/316L flange ANSI B16.5
A3J 8" 150lbs RF, 316/316L flange ANSI B16.5
A5J 10" 150lbs RF, 316/316L flange ANSI B16.5
-- JIS-Flanges --
KVJ 10K 150A RF, 316L flange JIS B2220
KDJ 10K 200A RF, 316L flange JIS B2220
K5J 10K 250A RF, 316L flange JIS B2220
-- JPI-Flanges --
LJJ 150A 150lbs RF, 316/316L flange JPI 7S-15
LKJ 200A 150lbs RF, 316/316L flange JPI 7S-15
LLJ 250A 150lbs RF, 316/316L flange JPI 7S-15
-- Miscellaneous--
XXJ With flange hub, 316L
XVU UNI-Flange 6"/DN150/150, 304
max 14.5lbs/PN1/1K, compatible with
6" 150lbs / DN150 PN16 / 10K 150
YY9 Special version, TSP-No. to be spec.
40 Output; Operation:
A 4-20mA HART; 4-line display VU331, envelope curve display on site
Y Special version, TSP-No. to be spec.
50 Housing:
C T12 Alu, coated IP65 NEMA4X, separate conn. compartment
Y Special version, TSP-No. to be spec.
60 Cable entry:
2Gland M20
3Thread G1/2
4 Thread NPT1/2
9 Special version, TSP-No. to be spec.
70 Weight + measure approval:
A NMi + PTB (<1mm) type approval
F NMi witnessed initial verificat. (<1mm) type approval
G PTB witnessed initial verificat. (<1mm) type approval
R Not selected; Inventory control version (3mm)
Y Special version, TSP-No. to be spec.
80 Additional option:
A Basic version
Y Special version
995 Marking:
1 Tagging (Tag), see additional spec.
FMR533- Complete product designation