Endress+Hauser Liquiphant M FTL51C - Page 34

Liquiphant M FTL51C
34 Endress+Hauser
A8N* 1" 150 lbs PFA (conductive) > 316/316L Flange ANSI B16.5 1.0 kg
BBK DN32 PN25/40 ECTFE >316L Flange EN 1092-1 (DIN 2527) 2.0 kg
BBL DN32 PN25/40 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 2.0 kg
BBM DN32 PN25/40 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 2.0 kg
BBN DN32 PN25/40 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 2.0 kg
BDK DN40 PN25/40 ECTFE >316L Flange EN 1092-1 (DIN 2527) 2.4 kg
BDL DN40 PN25/40 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 2.4 kg
BDM DN40 PN25/40 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 2.4 kg
BDN DN40 PN25/40 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 2.4 kg
BEK DN50 PN6 ECTFE >316L Flange EN 1092-1 (DIN 2527) 1.6 kg
BEL DN50 PN6 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 1.6 kg
BEM DN50 PN6 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 1.6 kg
BEN DN50 PN6 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 1.6 kg
BGK DN50 PN25/40 ECTFE >316L Flange EN 1092-1 (DIN 2527) 3.2 kg
BGL DN50 PN25/40 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 3.2 kg
BGM DN50 PN25/40 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 3.2 kg
BGN DN50 PN25/40 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 3.2 kg
BNK DN80 PN25/40 ECTFE >316L Flange EN 1092-1 (DIN 2527) 5.9 kg
BNL DN80 PN25/40 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 5.9 kg
BNM DN80 PN25/40 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 5.9 kg
BNN DN80 PN25/40 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 5.9 kg
BQK DN100 PN10/16 ECTFE >316L Flange EN 1092-1 (DIN 2527) 5.6 kg
BQL DN100 PN10/16 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 5.6 kg
BQM DN100 PN10/16 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 5.6 kg
BQN DN100 PN10/16 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 5.6 kg
B8K DN25 PN25/40 ECTFE >316L Flange EN 1092-1 (DIN 2527) 1.4 kg
B8L DN25 PN25/40 PFA (Edlon
TM
) >316L Flange EN 1092-1 (DIN 2527) 1.4 kg
B8M DN25 PN25/40 PFA (RubyRed) >316L Flange EN 1092-1 (DIN 2527) 1.4 kg
B8N DN25 PN25/40 PFA (conductive) >316L Flange EN 1092-1 (DIN 2527) 1.4 kg
CGS DN50 PN25/40 Enamel >1.0487 Flange EN 1092-1 (DIN 2527) 3.2 kg
CNS DN80 PN25/40 Enamel >1.0487 Flange EN 1092-1 (DIN 2527) 5.9 kg
KEK 10 K 50 ECTFE >316L Flange JIS B2238 1.7 kg
KEL 10 K 50 PFA (Edlon
TM
) >316L Flange JIS B2238 1.7 kg
KEM 10 K 50 PFA (RubyRed) >316L Flange JIS B2238 1.7 kg
KEN 10 K 50 PFA (conductive) >316L Flange JIS B2238 1.7 kg
YY9* Special version
30 Probe length; Type:
BK ....... mm ECTFE 0.9 kg/m
BL ....... mm PFA (Edlon
TM
) 0.9 kg/m
BM ....... mm PFA (RubyRed) 0.9 kg/m
BN ....... mm PFA (conductive) 0.9 kg/m
BS ....... mm Enamel 0.9 kg/m
CK ....... inch ECTFE 2.3 kg/100 in
CL ....... inch PFA (Edlon
TM
) 2.3 kg/100 in
CM ....... inch PFA (RubyRed) 2.3 kg/100 in
CN ....... inch PFA (conductive) 2.3 kg/100 in
CS ....... inch Enamel 2.3 kg/100 in
DK Length: type II** ECTFE
DL Length: type II** PFA (Edlon
TM
)
DM Length: type II** PFA (RubyRed)
DN Length: type II** PFA (conductive)
DS Length: type II** Enamel
YY Special version
**) If replacing devices: When vertically mounting a Liquiphant M FTL51C
with length II, the switch point is at the same level as for a Liquiphant II
FTL360, FTL365, FDL30, FDL35
40 Electronics; output:
A FEL50A PROFIBUS PA
D FEL50D Density/concentration
1 FEL51 2-wire 19 to 253 V AC
2 FEL52 3-wire PNP 10 to 55 V DC
4 FEL54 Relay DPDT 19 to 253 V AC, 19 to 55 V DC
5 FEL55 8/16 mA, 11 to 36 V DC
6 FEL56 NAMUR (L-H signal)
7 FEL57 2-wire PFM
20 Process connection: Additional weight