Fire-Lite MS-9200UD - Page 55

0DVWHU3URJUDPPLQJ/HYHO 3URJUDPPLQJ
068'31$ 
)RUH[DPSOHLIDGHWHFWRUZLWKDGGUHVVLVWREHFRQILJXUHGIRU3$6RSHUDWLRQ
✓ Select PAS Yes when editing the detector set to address 005
✓ Program the desired zone or zones to be activated by this detector, in this
example Z001
✓ Program an output, such as a control module that is to be activated by detector
005 by assigning the same zone to it; in this example Z001
✓ Program an output, such as a control module, for PAS activation by assigning
zone Z97 to it. This control module may be connected to a signaling device
used to indicate a PAS condition (do not use a Notification Appliance Circuit
for this purpose)
✓ Enable zones Z001 and Special Purpose Zone PAS 97 and set the PAS delay
timer to some value
:LWKWKHSUHFHGLQJSURJUDPVHWWLQJVZKHQWKHGHWHFWRUZLWKDGGUHVVLV
DFWLYDWHG]RQH=ZLOOFDXVHLWVDVVRFLDWHGFRQWUROPRGXOHWRDFWLYDWH
LPPHGLDWHO\VRXQGLQJWKHFRQQHFWHG3$6VLJQDOLQJGHYLFH)ROORZLQJWKH3$6
GHOD\WLPH]RQH=ZLOOFDXVHLWVDVVRFLDWHGFRQWUROPRGXOHWRDFWLYDWHDQGWKH
FRQWUROSDQHOZLOOLQLWLDWHDQDODUPFRQGLWLRQ
3UHVLJQDO
7KH3UHVLJQDORSWLRQSURJUDPVWKHGHWHFWRUWRGHOD\SDQHODFWLYDWLRQIRUD
SUHSURJUDPPHGWLPHGHOD\RIXSWRWKUHHPLQXWHVZKLOHDOORZLQJIRUYLVXDO
YHULILFDWLRQE\DSHUVRQ1RWHWKDWWKHDODUPUHOD\DQGFRPPXQLFDWRUZLOOUHVSRQG
WRWKHLQLWLDODODUPLPPHGLDWHO\,QDGGLWLRQ=RQHZLOODFWLYDWH7KLV]RQHFDQ
EHSURJUDPPHGWRDFRQWUROPRGXOHZKLFKPD\EHXVHGWRDFWLYDWHDVRXQGHURU
LQGLFDWRUZKLFKWKHLQVWDOOHUGHVLJQDWHVDVD3UHVLJQDOLQGLFDWLRQ
GRQRWXVHD
1RWLILFDWLRQ$SSOLDQFH&LUFXLWIRUWKLVSXUSRVH

To enable the Pre-signal feature,
press 3 while viewing Edit Detector Screen #3 until the display reads Pre-signal
Yes. Each press of the 3 key will cause the display to toggle between Pre-signal Yes
and Pre-signal No. Refer to 3UHVLJQDORQSDJH.
)RUH[DPSOHLIDGHWHFWRUZLWKDGGUHVVLVWREHFRQILJXUHGIRU3UH6LJQDO
RSHUDWLRQ
✓ Select Pre-signal Yes when editing the detector set to address 005
✓ Program the desired zone or zones to be activated by this detector, in this
example Z001
✓ Program an output, such as a control module that is to be activated by detector
005 by assigning the same zone to it; in this example Z001
✓ Program an output, such as a control module, for Pre-signal activation by
assigning zone Z98 to it. This control module may be connected to a signaling
device used to indicate a Pre-signal condition GRQRWXVHD1RWLILFDWLRQ
$SSOLDQFH&LUFXLWIRUWKLVSXUSRVH
✓ Enable zones Z001 and Special Purpose Zone Pre-signal 98 and set the Pre-
signal delay timer to some value
:LWKWKHSUHFHGLQJSURJUDPVHWWLQJVZKHQWKHGHWHFWRUZLWKDGGUHVVLV
DFWLYDWHG]RQH=ZLOOFDXVHLWVDVVRFLDWHGFRQWUROPRGXOHWRDFWLYDWH
LPPHGLDWHO\VRXQGLQJWKHFRQQHFWHGVLJQDOLQJGHYLFHWRLQGLFDWHWKH3UHVLJQDO
FRQGLWLRQ)ROORZLQJWKH3UHVLJQDOGHOD\WLPH]RQH=ZLOOFDXVHLWVDVVRFLDWHG
FRQWUROPRGXOHWRDFWLYDWHDQGWKHFRQWUROSDQHOZLOOLQLWLDWHDQDODUPFRQGLWLRQ
EDIT DETECTOR
1=WALKTEST
2=PAS
3=PRE-SIGNAL
Edit Detector Screen #3
See Page
