n
Configuration 1 (Key/LED 5)
The LED will go On to indicate that the system is ready
to start the programming procedure. Using the keys in
columns E and F, configure the Control panel:
– if the LED is On, the respective Module is included in
the configuration;
– if the LED is Off, the respective Module is NOT inclu
-
ded in the configuration.
During this phase, the keys and LEDs in columns E and
F will operate in accordance with the options written in
positive type:
Ø
Exting. 1 = Extinguishment Module nr. 1
Ø
Exting. 2 = Extinguishment Module nr. 2
Ø
Expander 1 = Expander Module nr. 1
Ø
Expander 2 = Expander Module nr. 2
Ø
Power 1 = Power Station nr. 1
Ø
Power 2 = Power Station nr. 2
Ø
Power 3 = Power Station nr. 3
Ø
Power 4 = Power Station nr. 4
n
Configuration 2 (Key/LED 7)
The LED will go On to indicate that the system is ready
to start the programming procedure. Using the keys in
columns E and F, configure the Control panel:
– if the LED is On, the respective Module is included in
the configuration;
– if the LED is Off, the respective Module is NOT inclu-
ded in the configuration.
During this phase, the keys and LEDs in columns E and
F will operate in accordance with the options written in
negative type:
Ø LCD 1 = LCD Module nr. 1
Ø LCD 2 = LCD Module nr. 2
Ø LCD 3 = LCD Module nr. 3
Ø LCD 4 = LCD Module nr. 4
Ø Rep. 1 = Repeater panel nr. 1
Ø
Rep. 2 = Repeater panel nr. 2
Ø
Rep. 3 = Repeater panel nr. 3
Ø
Rep. 4 = Repeater panel nr. 4
The “MODULES” Programming Phase
+
The Activation Mode may ONLY be programmed
THROUGH A PC.
The MODULES LED will blink to indicate that the system is
ready to program the parameters of the Extinguishment
Modules. During this phase, the keys and LEDs will opera
-
te in accordance with the options preceded by in the pa
-
nes on the Programming Overlay, see Figure 35.
The LED (Exting. 1 or Exting. 2) corresponding to the
Extinguishment Module concerned will blink to indicate that
the system is ready to program the respective parameters.
Press key 1 (Extinguish. Time), 2 (Pre-Exting. Time),
4 (Man. pre-Ext. T.), 5 (Reset Inhibit T.)or7 (Zones)
to select the parameter to be programmed, then read
the relevant sub-section, or press key 9 (Next Phase)
to go back to the ZONE Programming.
n
Extinguish. time (Key/LED 1)
The LED will go On to indicate that the system is ready
to start the programming procedure.
Use the Increase Time option (Key 8)orDecrease
Time option (Key 0), respectively, to increase or decre
-
ase the setting. The setting is achieved by adding toget
-
her the values preceded by and , indicated by the
LEDs in column B (e.g. if the 20 sec and 40 sec LEDs
are On, the setting will be 60 seconds (20+40)).
n Pre-exting. time (Key/LED 2)
The LED will go On to indicate that the system is ready
to start the programming procedure.
Use the Increase Time option (Key 8)orDecrease
Time option (Key 0), respectively, to increase or decre-
ase the setting. The setting is achieved by adding toget-
her the values preceded by and , indicated by the
LEDs in column B (e.g. if the 16 sec and 4 sec LEDs
are On, the setting will be 20 seconds (16+4)).
PROGRAMMING FROM THE PANEL 49
To Next Page
Loading...
