Flex CS 60 WET User Manual

CS 60 WET/CSW 4161
24
Switching on and off
`^rqflk>
cçê=êÉ~ëçåë=çÑ=ë~ÑÉíó=íÜÉ=ë~ÑÉíó= ëïáíÅ Ü=áë=åçí=
äçÅâÉÇ=~åÇ=ã ìëí=ÄÉ=ÜÉ äÇ=Ççï å=ÇìêáåÖ=ë~ïáåÖK
Switching on
 Press and hold down the switch
interlock (1.).
 Press and hold down the safety switch (2.).
 Release switch interlock (3.).
Switching off
 Release safety switch.
Switching on the power tool again
following a power failure
t^okfkd>
_ÉÑçêÉ=ëïáíÅÜáåÖ=çå=íÜÉ=éçïÉê=íççä=~Ö~áå=
ÑçääçïáåÖ=~=éçïÉê=Ñ~áäìêÉI=~äï~óë=ÇÉíÉêãáåÉ=
íÜÉ Å~ìëÉ=çÑ=íÜÉ=éçïÉê=Ñ~áäìêÉK=
aç= åçí =ëïáíÅÜ=çå=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=~Ö~áå=
ìåíáä=ë~ÑÉ=çéÉê~íáçå=áë=éçëëáÄäÉK=
`ÜÉÅâ=ÑìåÅíáçå=çÑ=íÜÉ=mo`a=ëïáíÅÜK
Setting the cutting depth
klqb
qç=ÉåëìêÉ=çéíáãìã=ÅìííáåÖ=êÉëìäíëI=íÜÉ Çá~J
ãçåÇJíáééÉÇ=ÅìííáåÖJçÑÑ=ïÜÉÉä=ã~ó éêçàÉÅí=
~ ã~ñáãìã=P=ãã=çìí=çÑ=íÜÉ=ïçêâéáÉÅÉK
 Pull out the mains plug.
 Release clamping lever for setting
the cutting depth (1.).
 Set required cutting depth (2.): Lift saw
off saw bench = shallower cutting depth.
 Tighten clamping lever (3.).
Setting the mitre angle
(CS 60 WET only)
klqb
få=íÜÉ=Å~ëÉ=çÑ=ãáíêÉ=ÅìíëI=íÜÉ=ÅìííáåÖ=ÇÉéíÜ=
áë êÉÇìÅÉÇX=áÑ=êÉèìáêÉÇ=êÉJ~ÇàìëíK
 Pull out the mains plug.
 Loosen clamping nut (1.).
 Set required mitre angle with the aid
of the scale (2.).
 Tighten clamping nut (3.).

Flex CS 60 WET Specifications

General

Brand	Flex
Model	CS 60 WET
Category	Saw
Language	English