FLOWmetrix SAFMAG BETA METER User Manual

Safmag House P.O.Box 17143 Int Tel.: +27(0)312060630
498 Sydney Road Congella SA Tel.: 086 110 6028
Congella South Africa, 4013 enquiries@flowmetrix.co.za
Durban Reg. No. CK 1986/011597/23 www.flowmetrix.co.za
USER’S GUIDE
Installation & Operation
Instructions
ΒETA METER
ELECTROMAGNETIC FLOWMETER
16

FLOWmetrix SAFMAG BETA METER Specifications

General

Brand	FLOWmetrix
Model	SAFMAG BETA METER
Category	Measuring Instruments
Language	English

Summary

Introduction and Theory

Theory of Operation

Explains the principle of electromagnetic induction for flow measurement.

Installation Guides

Remote Electronics Installation

Guidelines for mounting and positioning the remote display unit.

Flowtube Installation

Instructions for installing the fullbore flowtube sensor.

Meter Body and Guidelines

Application Guidelines

Recommended parameters for optimal flowmeter performance.

Safmag Magprobe

Magprobe Installation

Step-by-step guide for installing the Safmag Magprobe insertion sensor.

Wiring and Special Features

Wiring Diagram

Visual representation of electrical connections for the meter and display.

Empty Pipe Detection

Explanation of the EPD circuit and its activation.

General Operation and Output Signals

General Features

Overview of meter features, response time, and batching capabilities.

Output Functions Explained

Details on 4-20mA and open collector transistor output signals.

User Interface and Navigation

Keypad System Operation

Description of the 4-button programming system and navigation.

Menu System Navigation

Overview of the menu structure for programming and setup.

Programming and Setup Configuration

Main Menu Structure

Structure of the main menu for configuration options.

Batching Setup

Configuration setting for the batching function.

Password Management

Procedure for entering and managing the device password.

Unit Selection

Selection of measurement units for rate and total.

Menu-1 Access

Accessing the first level of menu settings.

Menu-2 Access

Accessing the second level of menu settings.

Save and Exit Procedure

How to save configuration changes and exit the menu.

Calibration Mode Access

Accessing the hidden calibration mode.

Batching Function Operation

Batching Function Steps

Detailed steps and operation of the batching function.

MENU-1 Flow Data Settings

Rate Units Configuration

Setting the units for flow rate measurement.

Maximum Flow Rate Setup

Configuring the maximum flow rate for 20mA output.

Low Flow Alarm Setting

Setting the low flow rate threshold for alarms.

High Flow Alarm Setting

Setting the high flow rate threshold for alarms.

Total Units Configuration

Selecting the units for total flow measurement.

Totaliser Options

Choosing between Grand total and resettable total.

MENU-1 Additional Configuration

Clear Total Options

Options for clearing or setting flow totals.

Batch Mode Control

Enabling or disabling the batching mode.

Damping Level Adjustment

Adjusting the damping levels for signal stability.

Cutoff Level Setting

Setting cutoff levels to ignore low flow signals.

Empty Pipe Detection Control

Activating or deactivating the empty pipe detection feature.

MENU-2 Setup Data Configuration

Mains Frequency Selection

Selecting the mains frequency for operation.

Sensor Type Selection

Choosing between flowtube and insertion mag sensor types.

Nominal Bore Input

Inputting the nominal bore diameter of the flowtube.

K-Value Entry

Entering the flow tube's calibration coefficient.

Z-Factor Calibration

Setting the zero calibration factor (Z-factor).

Output Simulation Percentage

Simulating output percentage for mA loop testing.

MENU-2 Output and Communication Settings

Volume per Pulse Setup

Setting the pulse rate for volume/pulse output.

Pulse Width Configuration

Configuring the pulse width for output signals.

OCT 1 Output Programming

Programming the first open collector transistor output function.

OCT 2 Output Programming

Programming the second open collector transistor output function.

OCT 3 Output Programming

Programming the third open collector transistor output function.

Modbus Slave Address Setting

Setting the Modbus slave address for communication.

Calibration Mode Procedures

Accessing Calibration Mode

Accessing and performing calibration procedures.

Setting 4mA Output Point

Setting the 4mA output point for calibration.

Setting 20mA Output Point

Setting the 20mA output point for calibration.

Modbus RTU Communication

Modbus Control Functions

Overview of Modbus function codes for communication.

RS-485 Wiring Overview

Guidelines for RS-485 serial wiring and termination.

Modbus Setup and Data Mapping

Modbus Setup Configuration

Configuring Modbus address and communication parameters.

Register and Coil Mapping

Mapping of data registers for Modbus communication.

Modbus Block Size Guidelines

Recommended maximum block sizes for Modbus communication.

Holding Register Details

Specific details on holding registers used in Modbus.

Error Messages and Troubleshooting

Error/Warning Message Reference

List of error messages and their potential causes.

Troubleshooting Common Problems

Guide to diagnosing and resolving common meter problems.

Features and Specifications

Technical Specifications Summary

Comprehensive list of technical features and specifications.

Flowtube Testing Procedures

Flowtube Testing Steps

Procedures for testing the flowtube component.

Extended Flowtube Testing

Further Testing Steps

Further steps for testing flowtube and signal converter.

Warranty and Returns Policy

Product Warranty Terms

Terms and conditions of the product warranty.

Goods Return Process

Steps for returning defective or damaged goods.