EasyManua.ls Logo

Fomotech FHSS Series - User Manual

Fomotech FHSS Series
49 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
A
A
l
l
p
p
h
h
a
a
6
6
0
0
0
0
X
X
J
J
F
F
H
H
S
S
S
S
S
S
e
e
r
r
i
i
e
e
s
s
I
I
n
n
d
d
u
u
s
s
t
t
r
r
i
i
a
a
l
l
R
R
a
a
d
d
i
i
o
o
R
R
e
e
m
m
o
o
t
t
e
e
C
C
o
o
n
n
t
t
r
r
o
o
l
l
S
S
y
y
s
s
t
t
e
e
m
m
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
&
&
P
P
a
a
r
r
t
t
s
s
M
M
a
a
n
n
u
u
a
a
l
l
Fomotech International Corp.

Table of Contents

Questions and Answers

  • R
    Rachel BakerAug 11, 2025
    What to do if Fomotech Remote Control transmitter does not communicate with the receiver?
    • W
      Wesley JonesAug 11, 2025
      If the Fomotech Remote Control transmitter isn't communicating with the receiver, there are a few potential causes: * **Low battery:** If the status LED blinks red or doesn't light up when you turn on the transmitter with the EMS elevated, turn the power off and replace the two alkaline “AA” batteries. * **Emergency stop button:** Ensure the emergency stop button is elevated. Turn off the transmitter, then turn it back on. * **Unpaired devices:** If the SQ light is off, the transmitter and receiver may need to be paired. Please refer to section 7.2.2 in the manual regarding RF module pairing.
  • H
    hguerraAug 17, 2025
    What to do if there is no power to the Fomotech Remote Control receiver?
    • G
      Gabriel BrownAug 17, 2025
      If there's no power to the Fomotech Remote Control receiver and the AC power indicator is off, the issue might be a blown fuse or a problem with the power connection. First, ensure the power input to the receiver unit is correct. If the indicator remains unlit, check the receiver for any open fuse.
  • M
    Michelle JamesAug 23, 2025
    Why does my Fomotech Remote Control have abnormal outputs?
    • J
      Joseph Taylor Jr.Aug 23, 2025
      Abnormal outputs from your Fomotech Remote Control may be due to incorrect receiver configuration or wiring. Please refer to sections 9 and 10 of the manual to verify that the receiver is correctly wired and configured for your specific application.
  • E
    eric39Aug 29, 2025
    How to fix a Fomotech Remote Control transmitter that won't communicate with the receiver?
    • J
      johnkennedyAug 29, 2025
      If the Fomotech Remote Control transmitter isn't communicating with the receiver, start by checking that the correct transmitter is being used, matching the RF channel and ID code with the receiver. These details are on the labels of both devices. Also, ensure the transmitter is powered on with the EMS elevated. If the status LED blinks red or doesn't light up, replace the two AA batteries after turning the power off.
  • R
    Renee MartinSep 4, 2025
    What to do if my Fomotech Remote Control transmitter doesn't communicate because the EMS is activated?
    • C
      Corey ReynoldsSep 4, 2025
      The Fomotech Remote Control transmitter might fail to communicate with the receiver if it's turned on while the EMS is activated (pressed down). To resolve this, elevate the EMS, then turn the power switch off and on again.

Fomotech FHSS Series Specifications

General IconGeneral
BrandFomotech
ModelFHSS Series
CategoryRemote Control
LanguageEnglish

Related product manuals