Franke Smart User Manual

FMO 45 GN 81 / FMO 45 GN 86
– 10 –
EN
This clearance shouldn‘t beignored
as it‘s required for ventilation system
oftheappliance tooperate.
Right Place For Installation
Product has been designed tobemounted
toworktops procured from market. asafe
distance must beleft between theproduct and
kitchen walls orfurniture. See thedrawings
provided on pages 120-121 for proper
distances (values inmm).

Used surfaces, synthetic laminates and
adhesives must beheat resistant
(minimum 100°C)‘

Kitchen cupboards must belevel with
product and secured.

If there isadrawer below theoven, arack
must beplaced between oven and drawer.
WARNING: Do not install theproduct next
torefrigerators orcoolers. Theheat emitted by
theproduct increases theenergy consumption
ofcooling devices.
WARNING: Do not use door and/or handle
tocarry ormove theproduct.
45cm Built-In Oven Installation and
Mounting
Place ofuse for product must belocated
before starting installation. Product mustn‘t
beinstalled inplaces which are under
theeffect ofstrong air flow. Carry theproduct
with minimum two people. Do not drag
theproduct so that floor isn‘t damaged.
Remove all transportation materials inside and
outside theproduct. Remove all materials and
documents intheproduct.
Installation Under Counter
(figure 1 page 120)
Cabin must match thedimensions provided
infigure2 (page 120).
A clearance must beprovided at therear
part ofthecabin as indicated inthefigure so
that necessary ventilation can beachieved.
After mounting, theclearance between lower
and upper part ofthecounter isindicated
infigure5 (page 121) with „A“. It‘s for
ventilation and shouldn‘t becovered.
Installation inanElevated Cabinet
(figure 4 page 121)
Cabin must match thedimensions provided
infigure4 (page 121). Theclearances with
thedimensions indicated inthefigure must
beprovided at therear part ofcabin, upper and
lower sections so that necessary ventilation
can beachieved.
Installation Requirements
Product dimensions are provided
inthefigure3(page 120). Furniture surfaces
for mounting and mounting materials
tobeusedmust have aminimum temperature
resistance of100°C. Mounting cabin must
besecured and its floor must beplane for
product not totilt over. Cabin floor must have
aminimum strength that would handle
aload of60kg.
Placing and Securing theOven

Place theoven into thecabin with two
ormore people.

Ensure that oven‘s frame and front edge
ofthefurniture match uniformly.

Supply cord mustn‘t beunder theoven,
squeeze inbetween oven and furniture
orbend.

Fix theoven tothefurniture by using
thescrews provided with theproduct.
Screws must bemounted as shown
infigure5 (page 121) by passing them
through plastics attached toframe
oftheproduct.

Screws mustn‘t beovertightened.

Otherwise, screw sockets might
beworn. Check that oven doesn‘t
move after mounting. ifoven
isn‘t mounted inaccordance with
instructions, there isarisk oftilt over
during operation.
Electrical Connection
Mounting place oftheproduct must have
appropriate electrical installation.
Network voltage must becompatible with
thevalues provided on type label ofproduct.
Product connection must bemade
inaccordance with local and national
electrical requirements. Before starting
themounting disconnect network power. Do
not connect theproduct tonetwork until its
mounting iscompleted.

Franke Smart Specifications

General

Energy Efficiency Class	A
Number of Functions	8
Voltage	220-240 V
Installation Type	Built-in
Color	Stainless Steel
Control Type	Electronic
Cooling Fan	Yes
Door	Double Glazed
Child Lock	Yes
Timer	Yes
Type	Built-in
Frequency	50/60 Hz