Franke Smart - Electrical Safety; Connection and Wiring Precautions

FMO 45 GN 81 / FMO 45 GN 86
– 6 –
EN

It isimportant toplace thewire grill and tray
properly on thewire racks and/or correctly
place thetray on therack. Place thegrill
ortray between two rails and make sure it
isbalanced before putting food on it.

Against therisk oftouching theoven
heater elements, remove excess parts
ofthebaking paper that hang over from
theaccessory orcontainer.

Never use it at higher oven temperatures
than themaximum usage temperature
indicated on your baking paper. Do not
place thebaking paper on thebase
oftheoven. Against therisk oftouching
theoven heater elements, remove excess
parts ofthebaking paper that hang over
from theaccessory orcontainer.

When thedoor isopen, do not place
any heavy object on thedoor orallow
children tosit on it. You may cause
theoven tooverturn orthedoor hinges
tobedamaged.

The packaging materials are dangerous for
children. Keep packaging materials away
from thereach ofchildren.

User should not handle theoven by himself.

During usage, theinternal and external
surfaces oftheoven get hot. As you open
theoven door, step back toavoid thehot
vapour coming out from theinterior. There
isrisk ofburning.

Do not place heavy objects when oven door
isopen, risk oftoppling.

Oven supply can bedisconnected during any
construction work at home. After completing
thework, re-connecting theoven shall
bedone by authorized service.

User should not dislocate theresistance
during cleaning. It may cause anelectric
shock.

Turn off theappliance before removing
thesafeguards. After cleaning, install
thesafeguards according toinstructions.

Cable fixing point shall beprotected.

Please don’t cook thefood directly on
thetray / grid. Please put thefood into
oron appropriate tools before putting them
intheoven.
Electrical Safety

Plug theappliance inagrounded
socket protected by afuse conforming
tothevalues specified inthetechnical
specifications chart.

Have anauthorized electrician set grounding
equipment. Our company shall not
beresponsible for thedamages that shall
beincurred due tousing theproduct without
grounding according tolocal regulations.

The circuit breaker switches oftheoven
shall beplaced so that end user can reach
them when theoven isinstalled.

The power supply cord (the cord with
plug) shall not contact thehot parts
oftheappliance.

If thepower supply cord (the cord with plug)
isdamaged, this cord shall bereplaced
by themanufacturer orits service agent
oranequally qualified personnel toprevent
ahazardous situation.

Never wash theappliance by spraying
orpouring water on it. There isarisk
ofelectrocution.

Do not use cut ordamaged cords orextension
cords other than the original cord.

Make sure that there isno liquid orhumidity
intheoutlet where theproduct plug
isinstalled.

The rear surface oftheoven also heats
up when theoven isoperated. Electrical
connections shall not touch therear
surface, otherwise theconnections
may bedamaged.

Do not tighten theconnecting cables
totheoven door and do not run them over
hot surfaces. ifthe cord melts, this may
cause theoven toshort circuit
and even afire.

Unplug theunit during installation,
maintenance, cleaning and repair.

If thepower supply cable isdamaged,
itmust bereplaced by its manufacturer
orauthorized technical service orany
other personnel qualified at thesame level,
inorder toavoid any dangerous situation.

Make sure theplug isinserted firmly into
wall socket toavoid sparks.

Do not use steam cleaners for cleaning
theappliance, otherwise electric shock
may occur.

An omnipolar switch capable todisconnect
power supply isrequired for installation.
Disconnection from power supply shall
beprovided with aswitch oranintegrated
fuse installed on fixed power supply
according tobuilding code.