Frymaster LOV User Manual (English)

Other manuals for Frymaster LOV

Quick Start2 pages

Technical Information Manual39 pages

Quick Reference2 pages

Guide2 pages

Questions and Answers:

M
Michael RichardsonAug 1, 2025
What to do if the add pump is not operating on a Frymaster LOV Fryer?
- K
  Kathleen HardyAug 1, 2025
  If the Add pump on your Frymaster Fryer isn't working, start by checking the voltage at the MIB board from Pin 1 to Pin 2. It should be 24 VAC. If it's not, inspect the connections from the RTI 24VAC transformer and the transformer itself at the RTI. Also, check the voltage at the MIB board from Pin 2 to Pin 3; it should also be 24 VAC. If not, the MIB board might be faulty, or the wires to the pump relay could be shorted. Finally, verify that the voltage at the Add pump relay is 24 VAC. If it isn't, check the wiring from the MIB board. The relay is located on top of the RTI system.
M
Michael WatersAug 5, 2025
What to do if the waste valve is not opening on a Frymaster Fryer?
- J
  John Holloway MDAug 5, 2025
  If the waste valve on your Frymaster Fryer isn't opening, check the voltage at the MIB board from Pin 1 to Pin 2. It should measure 24 VAC. If it doesn't, check the connections from the RTI 24VAC transformer and inspect the transformer at the RTI. Also, check the voltage at the MIB board from Pin 2 to Pin 4, which should also be 24 VAC. If it's not, the MIB board may be bad, or the wires to the waste valve may be shorted. Finally, verify the voltage at the waste valve itself; it should be 24 VAC. If not, check the wiring from the MIB board.
C
Cory ForbesAug 9, 2025
What to do if the JIB valve is not opening on a Frymaster LOV?
- M
  morrisglennAug 9, 2025
  If the JIB valve on your Frymaster Fryer isn't opening, check the voltage at the MIB board from Pin 1 to Pin 2. It should be 24 VAC. If it's not, check the connections from the RTI 24VAC transformer and the transformer itself at the RTI. Also, check the voltage at the MIB board from Pin 6 to Pin 7, which should also be 24 VAC. If it's not, the MIB board may be bad, or the wires to the JIB valve may be shorted. Finally, verify the voltage at the JIB valve itself; it should be 24 VAC. If it isn't, check the wiring from the MIB board.
S
Stanley TateAug 18, 2025
Why does one vat top off but other vats fail to top off on Frymaster LOV Fryer?
- C
  Christina VazquezAug 18, 2025
  If one vat tops off but other vats fail to top off in your Frymaster Fryer, it could be due to a failed solenoid. Check the power to the pump. If the pump is hot, the solenoid has probably failed. Another possible reason is a loose wire connection. Ensure all wiring harnesses are securely connected to the ATO board and solenoids.
C
Christine HillAug 22, 2025
What to do if incorrect vat tops off in Frymaster LOV?
- D
  Daniel CollinsAug 23, 2025
  If the incorrect vat is topping off in your Frymaster Fryer, it may be due to incorrect wiring. Ensure wires are wired correctly. Alternatively, the flexlines might be connected to the wrong vat. In this case, switch the flexlines to the correct vat.
R
Richard MartinezAug 27, 2025
How to fix yellow JIB low light that won’t illuminate on Frymaster Fryer?
- J
  Judith GreenAug 27, 2025
  If the yellow JIB low light won’t illuminate on your Frymaster Fryer, it could be due to several reasons: * The auto top off power switch may be off. Verify that the auto top off power switch is switched on. The switch is located behind the JIB on the left side of the auto top off control box. * Power in the component box may not be present. Ensure power is present in the component box. * The transformer may have failed. If power is present in the component box, check the transformer for correct voltage. * There may be a loose wire connection. Ensure the yellow LED is securely attached to plug J6 on the ATO board.