Fuji Electric FRENIC-Lift LM2C Series - Table of Contents

xiv
Table of Contents
Preface ................................................................................... i
 Safety precautions .............................................................. i
Conformity to the Low Voltage Directive in the EU ............... vi
Conformity with Canadian standards and U.S. standards .... ix
Product warranty ................................................................. xii
Chapter 1 BEFORE USE ................................................ 1-1
1.1 Acceptance Inspection and Appearance of
Product .................................................................. 1-1
1.2 Precautions for Using Inverters .............................. 1-2
1.3 Usage environment and Storage environment....... 1-3
1.3.1 Usage environment ....................................... 1-3
1.3.2 Storage environment ..................................... 1-4
Chapter 2 MOUNTING AND WIRING THE INVERTER .. 2-1
2.1 Installing the Inverter.............................................. 2-1
2.2 Wiring .................................................................... 2-2
2.2.1 Removing the front cover ............................. 2-2
2.2.2 Mounting the front cover ............................... 2-2
2.2.3 Recommended wire sizes ............................. 2-3
2.2.4 Terminal arrangement diagrams and screw
specifications................................................. 2-3
2.2.5 Terminal functions and wiring order ............... 2-7
2.2.6 Connection diagrams .................................. 2-12
2.2.7 Setting the slide switches on the control PCB
.................................................................... 2-16
2.2.8 Mounting and connecting the keypad to
the panel ..................................................... 2-16
Chapter 3 OPERATION USING THE KEYPAD ............... 3-1
Chapter 4 RUNNING THE MOTOR FOR A TEST ........... 4-1
4.1 Checking Prior to Powering ON ............................. 4-1
4.2 Powering ON and Checking................................... 4-1
4.3 Configuring the Function Code Data Before
Test Run................................................................. 4-2
4.4 Running the Inverter for Motor Operation Check ... 4-3
4.5 Preparation for Practical Operation ........................ 4-3
Chapter 5 TROUBLESHOOTING ................................... 5-1
5.1 Alarm Codes .......................................................... 5-1
Chapter 6 MAINTENANCE AND INSPECTION .............. 6-1
6.1 Daily Inspection ..................................................... 6-1
6.2 Periodic Inspection ................................................ 6-1
6.3 List of Periodic Replacement Parts ........................ 6-2
6.4 Inquiries about Product and Guarantee ................. 6-3
6.4.1 When making an inquiry ................................ 6-3
Chapter 7 SPECIFICATIONS .......................................... 7-1
7.1 Standard Model ...................................................... 7-1
7.2 External Dimensions .............................................. 7-3
Chapter 8 CONFORMITY WITH STANDARDS .............. 8-1
8.1 Compatibility with Revised EMC Directive
and Low Voltage Directive .................................... 8-1
8.2 Compliance with European Standards ................... 8-2
8.3 Conformity to the Low Voltage Directive
in the EU ................................................................ 8-2
8.4 Compliance with EMC Standards .......................... 8-3
8.4.1 General ......................................................... 8-3
8.4.2 Recommended installation procedure ........... 8-3
8.5 Harmonic Component Regulation in the EU .......... 8-4
8.5.1 General comments ........................................ 8-4
8.5.2 Compliance with IEC/EN 61000-3-2 .............. 8-4
8.6 Compliance with Functional Safety Standard......... 8-5
8.6.1 General ......................................................... 8-5
8.6.2 Notes for compliance to Functional Safety
Standard ....................................................... 8-7
8.6.3 Inverter output state when Safe Torque Off (STO)
is activated ................................................... 8-9
8.6.4 ECF alarm (caused by logic discrepancy) and
inverter output state ....................................8-11
8.7 Compliance with Canadian and U.S. Standards
(CSA certification) ................................................ 8-12
8.7.1 General ....................................................... 8-12
8.7.2 Considerations when using FRENIC-Lift (LM2C)
in systems to be certified by CSA................ 8-12