Fujitsu UTY-RNRUZ5 - Auto Off Timer Configuration; Weekly Timer Scheduling

(1) (2)
1
Air Flow Direction Setting
Back
Individual VT Hold
VT
Setting
01-01
01-05
01-02
01-06
01-03
01-07
01-04
01-08
Individual VT Hold Page 1/ 2
Back Reset
Next
Page
Unit 1
Unit 5
Unit 2
Unit 6
Unit 3
Unit 7
Unit 4
Unit 8
NOTES
• Tocleartheairowdirectionsettingofallthedisplayed
indoorunits,touch[Reset].When[Yes]oftheconrmation
screen is touched, the setting is cleared and switches to
theairowdirectionsettingof“VTsetting”(Referto3-2-1).
• When you want to change the order of the indoor units
displayed on the indoor unit selection screen, consult
your installer or service personnel.
(3) Theoutletportselectionscreenthatsetstheairow
direction is displayed. Touch the outlet port to be set.
Check the position of each outlet port based on “ ”
mark of the indoor unit body.
(3) Position of the mark
Indoor Unit 1
Back Reset
Outlet
1O
utlet 2
Outlet
3O
utlet 4
NOTES
• Whentheairowdirectionsettingof“VTsetting”(Refer
to 3-2-1) is set at the outlet port, “—” is displayed at the
outlet port screen.
• To clear all four outlet port settings, touch [Reset]. When
[Yes]oftheconrmationscreenistouched,thesetting
isclearedandswitchestotheairowdirectionsetting
of “VT setting” (Refer to 3-2-1).
(4) Theairowdirectionsetting
screen is displayed. Touch
[
] or [ ]andsettheairow
direction or “Swing”.
1
Indoor Unit 1
Cance
lO
K
Outlet 1
When the [OK] is touched, the display returns to the
screen of (3).
When the [Back] is touched at the screen of (3), the
display returns to the screen of (2).
When the [Back] is touched at the screen of (2), the
display returns to the screen of (1).
3-3 AutoO󰀨TimerSetting
When indoor unit operation is started by the Operation but-
ton of this unit, operation stops after the set time.
(1) Touchthe[AutoO󰀨Timer
Setting] on the “Main Menu”
screen. When the “Password
Verication”screenwasdis-
played, enter the password and
touch [OK].
Monitor
Next
Page
Page 1/ 2 Main Manu
Air Flow Direction
Setting
Weekly Timer
Setting
Auto Off Timer
Setting
Special Setting
EnabletheAutoO󰀨Timer
(2) “AutoO󰀨Timer”screenisdisplayed.Touchthe[Enable/
Disable]onthe“AutoO󰀨Timer”screen.
(3) “Enable/Disable” screen is displayed. Touch the [Enable].
When the [OK] is touched, the display returns to the “Auto
O󰀨Timer”screen.
(2) (3)
Enable /Disable [Disable]
[In 30 min.]
[ – ]
Operation Stop Time
Time Range Setting
Auto Off Timer
Fri 10:00AM
Cancel OK
Enable/Disable
Cancel OK
Enable
Disable
SettheOperationStopTime
(4) Touchthe[OperationStoptime]onthe“AutoO󰀨Timer”
screen.
(5) The “Operation Stop” time screen is displayed. Set the
time with [
] or [ ]. The time can be set within the 30
to 240 min. range in 10 min. units.
When the [OK] is touched, the display returns to the “Auto
O󰀨Timer”screen.
(4) (5)
Enable /Disable [Enable]
[In 30 min.]
[ – ]
Operation Stop Time
Time Range Setting
Auto Off Timer
Fri 10:00AM
Cancel OK
After the Manual Operation
Operation Stop Time
Cancel OK
In
min.
30
Fri 10:00AM
SetthetimerangeofAutoO󰀨Timer
(6) Touchthe[TimeRangeSetting]onthe“AutoO󰀨Timer”
screen.
(7) “Time Range Setting” screen is displayed. Touch the
[Time Range] .
(6) (7)
Enable /Disable [Enable]
[In 30 min.]
[ – ]
Operation Stop Time
Time Range Setting
Auto Off Timer
Fri 10:00AM
Cancel OK
Time Range [Continuous]
[
-- : -- ]
[
-- : -- ]
Start Time
End Time
Time Range Setting
Fri 10:00AM
Cancel OK
(8) “Time Range” is displayed.
When specifying a time range
forthe“AutoO󰀨Timer”,touch
[Range Spec.] and when
enabling the setting all day,
touch [Continuous].
Time Range
Cancel OK
Range Spec.
Continuous
When the [OK] is touched, the display returns to the
“Time Range Setting” screen. When the [Continuous] is
selected, go to (14).
(9) Touch the [Start Time] on the “Time Range Setting”
screen.
(10) “Start Time” screen is displayed. Set the Start Time by
touching [
] or [ ] on the “Start Time” screen.
(9) (10)
Time Range [Range Spec.]
[
-- : -- ]
[
-- : -- ]
Start Time
End Time
Time Range Setting
Fri 10:00AM
Cancel OK
Fri 10:00AM
Start Time
Cancel OK
hour
AM
08
min.
40
When the [OK] is touched, the display returns to the
“Time Range Setting” screen.
NOTE
Setting screen format corresponds to the preference of
the “Display format Setting”.
En-10