Fujitsu UTY-RNRUZ5 - Maintenance Operations

(7) (8)
Backup Unit
s[
2/16]
[Enable]Lag Operation
Lead Lag Setting Page 2/ 2
Back
Previous
Page
Backup Units
Cancel OK
2 Units
1 Unit
When touching [OK], the display returns to the “Lead Lag”
screen.
LagOperationSetting
If the room temperature remains high while after starting
the Lead lag operation, the stopped indoor unit will start the
operation.
During the Lag operation,
blinks on the remote controller
display.
When the room temperature approaches to the set tempera-
ture,theLagoperationnishes.
(9) Touch the [Lag Operation] on the “Lead Lag” screen.
(10) “Lag Operation” screen is displayed. Touch the [Enable]
or [Disable].
(9) (10)
Backup Unit
s[
2/16]
[Enable]Lag Operation
Lead Lag Setting Page 2/ 2
Back
Previous
Page
Lag Operation
Cancel OK
Enable
Disable
When touching [OK], the display returns to the “Lead Lag”
screen.
Leadlagoperationenable/disable
(11) Touch the [Enable/Disable] on the “Lead Lag” screen.
(12) “Enable/Disable” screen is shown. Touch the [Enable] or
[Disable].
(11) (12)
Enable/Disable [Enable]
[7 Day]
[10min.]
Cycle
Over Lap Time
Lead Lag Setting Page 1/ 2
Next
Page
Back
Enable/Disable
Cancel OK
Enable
Disable
When touching [OK], the Lead lag operation starts or stops.
The display returns to the “Lead Lag” screen.
If you enable the Lead lag operation while the air condition-
ers are stopped, they start the operation following the Lead
lag setting.
If you disable the Lead lag operation, each indoor unit keeps
the current operation/stop status.
QuittheLeadlagsetting
To quit the Lead lag setting, touch
[Back]. If the Lead lag operation
is enabled, the screen moves to
the monitor mode screen. If it is
disabled, the screen moves to the
“Initial setting” screen.
Enable/Disable [Enable]
[7 Day]
[10min.]
Cycle
Over Lap Time
Lead Lag Setting Page 1/ 2
Next
Page
Back
3-9 Maintenance (for administrator)
Verication,operation,andsettingforadministratorinforma-
tion are performed.
(1) Touch the [Maintenance] on the “Main Menu” screen.
(2) When“PasswordVerication”screenisdisplayed,enter
the Password (or Installer Password) and touch [OK].
(1) (2)
Monitor
Previous
Page
Page 2/ 2 Main Menu
Summer Time
Setting
Initial Setting Maintenance
Preference
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Password Verification
Enter Current Password
(3) If the password is entered correctly, the “Maintenance”
screen is displayed. The screen has 3 pages which
are switched by touching the [Next Page] or [Previous
Page].
Back
Next
Page
Page 1/ 3 Maintenance
Error History
Setting
Status List
Version
Filter Sign
Reset
Previous
Page
Back
Next
Page
Page 2/ 3 Maintenance
Test Run
R.C. Address
Setting
Function Setting
I.U. Address
Verification
Back
Previous
Page
Page 3/ 3 Maintenance
Initialization
Installer Password
Change
Display Sensor
Values
Verication,operation,andsettingofthefollowingcon-
tentsareperformed.(♦:forinstaller)
(*:Itemsthatindoorunitdoesnotsupportarenotdis-
played.)
• ErrorHistory:
Theerrorhistorycanbeveried/cleared.
• SettingStatusList:
Thestatusofeachsettingcanbeveriedasalist.
• FilterSignReset*:
Aftertheindoorunitlteriscleaned,theltersigncan
be reset.
• Version:
ThesoftwareversionNo.ofthisunitcanbeveried.
• TestRun♦
• R.C.AddressSetting♦
• IndoorUnitAddressVerication♦
• FunctionSetting♦
• DisplaySensorValues♦
• InstallerPasswordChange♦
• Initialization♦
When the [Back] is touched at settings other than initial-
ization, the display returns to the “Main Menu” screen.
When initialization is performed, the setting screen at
initial starting is displayed.
En-23