Fujitsu UTY-RNRUZ5 - Vacation and Child Lock Features; Unit Stop and Emergency Functions

< Error Information screen >
[Error Information] is displayed only when there is an error
history. When the [Error Information] is touched, the display
switches to “Error Information” screen. Refer to [5-3 Error
Code] for the errors.
Status
Air Flow Direction
VT
Off
13
Off
HZ
Economy
Individual
Anti Freeze
Page 1/ 4
Monitor
Next
Page
Error
Information
02-01
14,15, 41, 44
Error Information Page 1/ 5
Address
Error Code
Back
Next
Page
1-1-3 Vacation
When the room will be empty for a long time due to vaca-
tion, etc., disable the indoor units schedule and continue the
unoccupiedstatebythefollowingoperation:
(1) Touch the [Vacation] on the Monitor Mode Screen.
NOTE
In the following state, [Vacation] is not displayed on the
Monitor Mode Screen.
• Scheduleisnotset.Referto[3SETTING]→[3-4
Weekly Timer Setting].
• Indoor Unit Stop is enabled. Refer to [1-1-5 Indoor Unit
Stop].
(2) The “Vacation” screen is displayed, and the following
statesarecontinued:
• The indoor units enter the unoccupied state. (When
[Away] is set, the set value is displayed and when the
room temperature reaches the set value, [Away Op-
eration] is performed.)
• [Disable] is set to the Schedule.
(1) (2)
76°F
76°F
80°F
80°F
74°F
74°F
84°F
68°F
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
Room Temp.
Cool
Heat
Away
Occupied
Vacation
Cancel
Fri 10:00AM
Away Operation
(3) When “Cancel” is touched, [Vacation] is reset and the
display returns to the Monitor Mode Screen. Schedule
returns to [Enable].
1-1-4 Child Lock
When this screen is displayed by
touching the monitor mode screen,
the unit is in child safety lock.
Child Lock ValidChild Lock Valid
• Childsafetylockset/reset:
Press the Operation button for 4 seconds or more while
touching an area outside the operation section of the moni-
tor mode screen (no response even if touched). Set/reset
can be performed even while the indoor unit is stopped.
The setting cannot be performed at screens other than the
monitor mode screen.
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
76°F
76°F
80°F
80°F
74°F
74°F
84°F
Room Temp.
Cool
68°FHeat
Away
Occupied
1-1-5 IndoorUnitStop
When cleaning an indoor unit or when the room is not used,
etc., the indoor unit can be stopped. When setting, temporar-
ily stop the indoor units and disable the following functions
so that they cannot be operated automatically. During this
time, an icon is displayed on the Monitor Mode Screen.
• Weekly Timer Setting
• Away Setting
When reset, disabled functions are also reset.
• IndoorUnitStopset/reset:
Press the Operation button for 5 seconds or more. Set/
Reset is possible in the occupied, unoccupied, and Away
operation states. The setting cannot be performed at
screens other than the Monitor Mode Screen.
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
76°F
76°F
80°F
80°F
74°F
74°F
84°F
Room Temp.
Cool
68°FHeat
Away
Occupied
Operation button
NOTE
Operation button can be operated even if Indoor Unit Stop
is enabled.
1-1-6 EmergencyStop
This screen is displayed when the
system was emergency stopped by
operation from the outside. When
emergency stop is reset, the moni-
tor mode screen is displayed.
Emergency Stop
En-7