Fujitsu UTY-RNRUZ5 - Control Operations; Operation On;Off Control; Operation Settings

2 CONTROL
2-1 OperationOn/O󰀨
(Occupied/Unoccupied)
(1) Press the Operation button.
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
76°F
76°F
80°F
80°F
74°F
74°F
84°F
Room Temp.
Cool
68°FHeat
Away
Occupied
Operation button
Power indicator lamp
The Power indicator lamp remains lit while the indoor
unit is operating.
NOTES
• The Operation button cannot be operated at screens
other than the Monitor Mode Screen.
• Depending on the occupied state and the indoor unit op-
eration state, the operation button needs to be pressed
twice.Referto[4OPERATIONTIPS]→[4-5Occupied
state].
2-2 OperationSettings
2-2-1 SettheOperationMode
(1) Touch the [Mode] on the monitor mode screen.
(2) “Mode” screen is displayed. Select the operation mode.
(1) (2)
76°F
76°F
80°F
80°F
74°F
74°F
84°F
68°F
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
Room Temp.
Cool
Heat
Away
Occupied
Mode
Cancel
Cool Dry Heat
Fan
OK
Custom
Auto
NOTES
• Only selectable modes are displayed. The selectable
modesmaybedi󰀨erentdependingonthesystemcon-
gurationandoperationstatus.Referto[4.OPERATION
TIPS]→[4-1SelectableModes].
• When the “Fan” is selected, the
temperature cannot be set.
76°F
76°F
84°F
68°F
AutoFan
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
Room Temp.
Cool
Heat
Away
Occupied
• The mode cannot be changed during Away operation.
Select the occupied state.
• [Custom Auto] mode can be used in the R.C. Group
to which Master Indoor Unit is set. It is not displayed
at other R.C. Group. It is not displayed at other indoor
units.
• When the following settings are not performed together,
[Custom Auto] cannot be used.
R.C.SensorSetting:Used.
Referto[3SETTING]→[3-8InitialSetting]→[3-8-5
R.C. Sensor Setting].
MasterIndoorUnitSetting:MasterIndoorUnit
For installer. Consult authorized service personnel.
• When the operation mode is switched in a heat recovery
system, operation preparations may take some time, but
this is not a malfunction.
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
2-2-2 SettheTemperature
(1) Touch the [Set Temp.] on the
monitor mode screen.
76°F
76°F
80°F
80°F
74°F
74°F
84°F
68°F
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
Room Temp.
Cool
Heat
Away
Occupied
(2) “Set Temp.” screen is displayed. Adjust the room tem-
perature with the [ ] or [ ].
Custom Auto mode Cool, Dry or Heat mode
74 80
°F°F
Set Temp.
Cancel OK
HeatCool
80
80
°F
°F
Set Temp.
Cance
lO
K
NOTES
• Thesettabletemperaturerangeisdi󰀨erentdepend-
ing on the operation mode. Refer to [4 OPERATION
TIPS]→[4-3Settabletemperaturerange].
• When the “Set Temp. Range Setting” is set, the select-
able temperature conforms to the setting. Refer to [3
SETTING]→[3-5SpecialSetting]→[3-5-3SetTemp.
Range Setting].
• During Away operation, the temperature cannot be set.
Select the occupied state.
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
2-2-3 SettheFanSpeed
(1) Touch the [Fan] on the monitor mode screen.
(2) “Fan” screen is displayed. Select the fan speed with the
[
] or [ ].
(1) (2)
76°F
76°F
80°F
80°F
74°F
74°F
84°F
68°F
Custom
Auto
Auto
Cool
Heat
Set Temp.
Mode
MenuStatus
Vacation
Fan
Fri 10:00AM
Room Temp.
Cool
Heat
Away
Occupied
Fan
Cancel OK
Auto
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
En-8