9
CONTENTS AND TECHNICAL SPECIFICATIONS
(Specifications and ratings are subject to change without notice.)
Your 9CAP super or 9CHP super (packaged with a 8 or 9-channel PCM receiver), 9CAF super or 9CHF super
(packaged with an 8-channel FM receiver) system includes the following components:
• 9C super Transmitter, including RF module (TP)
• R138DF, R148DF, R138DP, or R149DP Receiver
• Servos, S3151, S9252, S3001 or S9001, with mounting
hardware and servo arm assortment
• Switch harness
• Aileron extension cord
• 110V wall charger (North America)
• Frequency Flag
*
The set contents depend on the type of set.
*
Transmitter band may only be changed by changing the module. Contact Futaba Service
Center regarding adjustability of receiver band. Band cannot be changed by simply changing
crystals.
Transmitter T9C super
Operating system: 2-stick, 9 channels, PCM1024 system
Transmitting frequency: 29, 35, 36, 40, 41, 50, 72 or 75
MHz bands
Modulation: FM/PPM or PCM, switchable
Power supply: 9.6V NT8S700B Ni-Cd battery
Current drain: 280 mA
Receiver R149DP
(PCM Dual conversion)
Receiving frequency: 29, 35, 36, 40, 41, 50, or 72 MHz bands
Intermediate freq.: 10.7 MHz & 455 kHz
Power requirement: 4.8 - 6.0V Ni-Cd battery
Current drain: 14 mA
Size: 1.28 x 2.17 x 0.82 in. (32.6 x 55.0 x 20.8 mm)
Weight: 1.22 oz. (34.5 g)
Channels: 9
Receiver R138DP
(PCM Dual conversion)
Receiving frequency: 75 MHz bands
Intermediate freq.: 10.7 MHz & 455 kHz
Power requirement: 4.8 - 6.0V Ni-Cd battery
Current drain: 27 mA
Size: 2.56 x 1.42 x 0.85 in. (65 x 36 x 21.5 mm)
Weight: 1.42 oz. (40.3 g)
Channels: 8
Receiver R148DF
(FM Dual conversion)
Receiving frequency: 50 or 72 MHz bands
Intermediate freq.: 10.7MHz & 455 kHz
Power requirement: 4.8 - 6.0V Ni-Cd battery
Current drain: 14 mA
Size: 1.0 x 2.2 x 0.9 in. (25.4 x 55.8 x 22.9 mm)
Weight: 1.1 oz. (31.2 g)
Channels: 8
Receiver R138DF
(FM Dual conversion)
Receiving frequency: 35 or 40 MHz bands
Intermediate freq.: 10.7MHz & 455 kHz
Power requirement: 4.8 - 6.0V Ni-Cd battery
Current drain: 20 mA
Size: 2.56 x 1.42 x 0.85 in. (65 x 36 x 21.5 mm)
Weight: 1.42 oz. (40.3 g)
Channels: 8
Servo S9252 (Digital servo)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 91.7 oz.-in. (6.6 kg-cm) at 4.8V
Operating speed: 0.14 sec/60 at 4.8V
Size: 1.57 x 0.79 x 1.44 in. (40 x 20 x 36.6 mm)
Weight: 1.76 oz. (50 g)
Servo S3151 (Standard, Digital servo)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 43.1 oz.-in. (3.1 kg-cm) at 4.8V
Operating speed: 0.21 sec/60 at 4.8V
Size: 1.59 x 0.79 x 1.42 in. (40.5 x 20 x 36.1 mm)
Weight: 1.48 oz. (42 g)
Servo S9001 (Coreless motor)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 - 6.0V (from receiver)
Output torque: 54.2 oz.-in. (3.9 kg-cm) at 4.8V
Operating speed: 0.22 sec/60 at 4.8V
Size: 1.59 x 0.78 x 1.41 in. (40.4 x 19.8 x 36 mm)
Weight: 1.69 oz. (48 g)
Servo S3001 (Standard, ball-bearing)
Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 - 6.0V (from receiver)
Output torque: 41.7 oz.-in. (3.0 kg-cm)
Operating speed: 0.22 sec/60
Size: 1.59 x 0.78 x 1.41 in. (40.4 x 19.8 x 36 mm)
Weight: 1.59 oz. (45.1g)
To Next Page
Loading...
Need help?
General
