GE 469

GE Power Management 469 Motor Management Relay E-3
APPENDIX E E.1 FIGURES AND TABLES
E
E.1.2 LIST OF TABLES
T
ABLE
: 1–1 METERING AND ADDITIONAL FEATURES............................................................................................ 1-3
T
ABLE
: 2–1 469 TERMINAL LIST ................................................................................................................................ 2-7
T
ABLE
: 4–1 469 STANDARD OVERLOAD CURVE MULTIPLIERS.......................................................................... 4-33
T
ABLE
: 4–2 RTD TEMPERATURE VS. RESISTANCE.............................................................................................. 4-58
T
ABLE
: 4–3 ANALOG OUTPUT PARAMETER SELECTION TABLE ........................................................................ 4-79
T
ABLE
: 5–1 ACTUAL VALUES MESSAGES................................................................................................................ 5-1
T
ABLE
: 5–2 3-PHASE WYE VT CONNECTION......................................................................................................... 5-16
T
ABLE
: 5–3 3-PHASE OPEN DELTA VT CONNECTION ..........................................................................................5-16
T
ABLE
: 5–4 CAUSE OF EVENTS .............................................................................................................................. 5-25
T
ABLE
: 5–5 FLASH MESSAGES ............................................................................................................................... 5-28
T
ABLE
: 6–1 469 MEMORY MAP ................................................................................................................................ 6-18
T
ABLE
: 6–2 MEMORY MAP DATA FORMATS ........................................................................................................ 6-61
T
ABLE
: 7–1 PHASE CURRENT TEST ......................................................................................................................... 7-2
T
ABLE
: 7–2 INPUT VOLTAGE TEST........................................................................................................................... 7-2
T
ABLE
: 7–3 DIFFERENTIAL AND GROUND CURRENT TEST (5 A) ......................................................................... 7-3
T
ABLE
: 7–4 DIFFERENTIAL AND GROUND CURRENT TEST (1 A) ......................................................................... 7-3
T
ABLE
: 7–5 50:0.025 CT GROUND CURRENT TEST................................................................................................. 7-4
T
ABLE
: 7–6 100 Ω PLATINUM TEST........................................................................................................................... 7-4
T
ABLE
: 7–7 120 Ω NICKEL TEST ................................................................................................................................ 7-5
T
ABLE
: 7–8 100 Ω NICKEL TEST ................................................................................................................................ 7-5
T
ABLE
: 7–9 10 Ω COPPER TEST................................................................................................................................ 7-5
T
ABLE
: 7–10 DIGITAL INPUTS.................................................................................................................................... 7-6
T
ABLE
: 7–11 ANALOG I/O TEST 4-20
M
A................................................................................................................... 7-7
T
ABLE
: 7–12 ANALOG I/O TEST 0-1
M
A..................................................................................................................... 7-7
T
ABLE
: 7–13 OUTPUT RELAYS.................................................................................................................................. 7-8
T
ABLE
: 7–14 OVERLOAD TEST (STANDARD CURVE #4) ........................................................................................7-9
T
ABLE
: 7–15 POWER MEASUREMENT TEST ......................................................................................................... 7-10
T
ABLE
: 7–16 CURRENT UNBALANCE TEST ........................................................................................................... 7-12
T
ABLE
: 7–17 VOLTAGE PHASE REVERSAL TEST.................................................................................................. 7-12
T
ABLE
: 7–18 SHORT CIRCUIT TIMING .................................................................................................................... 7-13
T
ABLE
: A–1 SETPOINTS PAGE 1 – 469 SETUP ........................................................................................................A-1
T
ABLE
: A–2 SETPOINTS PAGE 2 – SYSTEM SETUP................................................................................................A-1
T
ABLE
: A–3 SETPOINTS PAGE 3 – DIGITAL INPUTS...............................................................................................A-2
T
ABLE
: A–4 SETPOINTS PAGE 4 – OUTPUT RELAYS .............................................................................................A-4
T
ABLE
: A–5 SETPOINTS PAGE 5 – PROTECTION....................................................................................................A-5
T
ABLE
: A–6 SETPOINTS PAGE 6 – CURRENT ELEMENTS .....................................................................................A-6
T
ABLE
: A–7 SETPOINTS PAGE 7 – MOTOR STARTING........................................................................................... A-7
T
ABLE
: A–8 SETPOINTS PAGE 8 – RTD TEMPERATURE........................................................................................A-8
T
ABLE
: A–9 SETPOINTS PAGE 9 – VOLTAGE ELEMENTS......................................................................................A-9
T
ABLE
: A–10 SETPOINTS PAGE 10 – POWER ELEMENTS ...................................................................................A-10
T
ABLE
: A–11 SETPOINTS PAGE 11 – MONITORING..............................................................................................A-11
T
ABLE
: A–12 SETPOINTS PAGE 12 – ANALOG I/O.................................................................................................A-12
T
ABLE
: A–13 SETPOINTS PAGE 14 – TWO-SPEED MOTOR .................................................................................A-13