GE 469

vi
469 Motor Management Relay
GE Power Management
INDEX
description ...............................................................2-18
operatin
g
.................................................................4-25
reset mode...............................................................4-24
R6 SERVICE RELAY
description ...............................................................2-18
reset mode...............................................................4-24
REACTIVE POWER
consumption specifications ........................................ 1-8
meterin
g
..................................................................5-12
setpoints ..................................................................4-68
specifications ............................................................ 1-8
REACTIVE POWER DEMAND .....................................5-13
REACTIVE POWER TRIPS .........................................5-21
REAL POWER
consumption specifications ........................................ 1-8
meterin
g
..................................................................5-12
specifications ............................................................ 1-8
REAL POWER DEMAND.............................................5-13
REAL TIME CLOCK ...............................................4-6, 5-8
REDUCED RTD LEAD NUMBER .................................2-16
REDUCED VOLTAGE START
auxiliary A status input .............................................4-15
auxiliary B status input .............................................4-15
contactor control circuit ............................................4-14
current characteristics ..............................................4-15
setpoints ..................................................................4-14
specifications ............................................................ 1-7
REDUCED WIRING RTDs ...........................................2-16
RELAY ASSIGNMENT PRACTICES ............................. 4-2
RELAY RESET MODE .......................................4-24, 4-25
REMOTE ALARM........................................................4-18
REMOTE ALARM STATUS........................................... 5-5
REMOTE RESET ........................................................4-16
REMOTE SWITCH ....................................................... 1-7
REMOTE TRIP ...........................................................4-18
REMOVING THE 489 FROM THE CASE....................... 2-5
RESET........................................................................ 4-1
RESET MOTOR INFORMATION..................................4-10
RESET STARTER INFORMATION...............................4-10
RESET, REMOTE.......................................................4-16
RESETTING THE 469.................................................4-24
RESIDUAL .................................................................4-11
RESIDUAL GROUND CONNECTION...........................2-10
RESTART BLOCK
emer
g
ency restart ....................................................4-16
setpoints ..................................................................4-56
specifications ............................................................ 1-7
RESTART, EMERGENCY ...........................................4-16
REVERSE POWER.....................................................4-70
REVERSE POWER TRIPS ..........................................5-21
ROLLING DEMAND ....................................................4-75
RS232...................................................................4-6, 6-1
RS232 PORT............................................................... 3-3
RS485
description ........................................................2-20, 6-1
wirin
g
dia
g
ram
..........................................................2-20
RS485 COMMUNICATIONS
see COMMUNICATIONS and SERIAL PORTS
RTD
actual values...................................................5-10, 5-18
alternate
g
roundin
g
..................................................2-17
ambient...........................................................4-57, 4-61
bearin
g
...........................................................4-57, 4-59
bias ................................................................4-44, 4-45
clearin
g
RTD data ..................................................... 4-9
description ...............................................................2-15
g
roundin
g
................................................................2-17
maximums ............................................... 4-9, 4-16, 5-18
open RTD sensor .....................................................4-62
other............................................................... 4-57, 4-60
reduced lead number................................................2-16
reduced wirin
g
.........................................................2-16
sensor connections ..................................................2-15
setpoints..................................................................4-57
short/low temp .........................................................4-62
specifications .............................................................1-7
stator.......................................................................4-58
temperatures............................................................5-10
types .......................................................................4-57
wirin
g
.......................................................................2-15
RTD 11 ......................................................................4-60
RTD 12 ......................................................................4-61
RTD 1-6 .....................................................................4-58
RTD 7-10 ...................................................................4-59
RTD ACCURACY TEST ................................................7-4
RTD BIAS
curve
.......................................................................4-45
description ...............................................................4-44
enablin
g
...................................................................4-28
setpoints..................................................................4-28
RTD LEAD COMPENSATION ......................................2-17
RTD MAXIMUMS ........................................................5-18
RTD SHORT/LOW TEMP ............................................4-62
RTD TEMPERATURE vs RESISTANCE .......................4-57
RTD TYPES ...............................................................4-57
RTDs 1 to 6................................................................4-58
RTDs 7 to 10 ..............................................................4-59
RUNNING HOURS......................................................4-16
S
S1 469 SETUP .............................................................4-4
S10 POWER ELEMENTS ............................................4-66
S11 MONITORING .....................................................4-72
S12 ANALOG I/O........................................................4-77
S13 469 TESTING ......................................................4-83
S14 TWO-SPEED MOTOR..........................................4-88
S2 SYSTEM SETUP ...................................................4-11
S3 DIGITAL INPUTS...................................................4-16
S4 OUTPUT RELAYS .................................................4-24
S5 THERMAL MODEL ................................................4-26
S6 CURRENT ELEMENTS ..........................................4-46
S7 MOTOR STARTING ...............................................4-53
S8 RTD TEMPERATURE ............................................4-57
S9 VOLTAGE ELEMENTS...........................................4-63
SAFE STALL CURVES ...............................................4-39
SAFE STALL TIME .....................................................4-30
SEAL ON DRAWOUT UNIT ...........................................2-1
SECONDARY INJECTION TEST SETUP .......................7-1
SERIAL COMM CONTROL..........................................4-13
SERIAL COMMUNICATIONS
see COMMUNICATIONS
SERIAL NUMBER.......................................................5-26
SERIAL PORTS
description ...............................................................2-20
setpoints..................................................................4-13
wiring diagram
........................................................2-20
SERVICE RELAY