GE G60 - Page 778

viii G60 Generator Protection System GE Multilin
INDEX
REMOTE INPUTS
actual values ...................................................................6-4
FlexLogic operands...................................................... 5-145
Modbus registers ..................................................B-11, B-18
settings ....................................................................... 5-299
specifications................................................................. 2-23
REMOTE OUTPUTS
DNA-1 bit pair.............................................................. 5-300
Modbus registers ..................................................B-69, B-70
UserSt-1 bit pair .......................................................... 5-301
REMOTE RTD INPUTS
Modbus registers ...........................................................B-48
REMOTE RTD PROTECTION
FlexLogic operands...................................................... 5-142
REMOTE SETTING AUTHORIZATION ................................4-2
REPAIR ................................................................... 11-8, G-8
REPLACEMENT MODULES..................................... 2-13, 2-14
REQUIREMENTS FOR INSTALLATION...............................1-6
RESET TO FACTORY DEFAULTS ......................................5-8
RESETTING..................................................5-8, 5-146, 5-301
to factory defaults ............................................................5-8
RESTRICTED GROUND FAULT
actual values ................................................................. 6-25
FlexLogic operands...................................................... 5-142
Modbus registers ..................................................B-12, B-55
settings ....................................................................... 5-199
specifications................................................................. 2-15
REVISION HISTORY ......................................................... G-1
RF IMMUNITY..................................................................2-29
RFI, CONDUCTED ........................................................... 2-29
RMS CURRENT ............................................................... 2-21
RMS VOLTAGE................................................................ 2-21
RRTD INPUTS
settings ....................................................................... 5-313
RS232
configuration ................................................................. 1-10
specifications................................................................. 2-27
wiring ............................................................................ 3-25
RS422
configuration ................................................................. 3-36
timing ............................................................................3-37
two-channel application.................................................. 3-36
with fiber interface ......................................................... 3-38
RS485
description..................................................................... 3-27
specifications................................................................. 2-27
RTD INPUTS
actual values ................................................................. 6-27
Modbus registers ..................................................B-20, B-33
settings .............................................................5-311, 5-314
specifications................................................................. 2-22
RTD PROTECTION
FlexLogic operands...................................................... 5-142
specifications................................................................. 2-19
S
SALES OFFICE..................................................................1-2
SAVING SETTING DOES NOT TAKE RELAY OUT OF SERVICE
2-3, 5-8
SBO ................................................................................5-54
SCAN OPERATION ............................................................1-4
SECURITY
delete files and records.................................................. 11-7
SELECT BEFORE OPERATE............................................ 5-54
SELECTOR SWITCH
actual values................................................................... 6-7
application example......................................................5-263
FlexLogic operands ......................................................5-143
logic ............................................................................5-264
Modbus registers........................................................... B-54
settings........................................................................5-259
specifications .................................................................2-20
timing ............................................................... 5-262, 5-263
Self-test errors .................................................................7-12
SELF-TESTS
description ...................................................................... 7-6
error messages ............................................................... 7-7
FlexLogic operands ......................................................5-146
Modbus registers............................................................. B-9
SENSITIVE DIRECTIONAL POWER
actual values..................................................................6-24
characteristic ...............................................................5-238
FlexLogic operands ......................................................5-139
logic ............................................................................5-239
Modbus registers.................................................. B-12, B-39
settings............................................................. 5-237, 5-239
specifications .................................................................2-16
SERIAL NUMBER .............................................................6-30
SERIAL PORTS
Modbus registers........................................................... B-26
SERVICE LIFE EXPECTED...............................................1-21
SETTING GROUPS ......................... 5-143, 5-159, 5-257, B-37
SETTINGS
change does not take relay out of service.................. 2-3, 5-8
SETTINGS FILE ................................................................ 4-1
takes relay out of service when loaded ............................. 4-2
SETTINGS TEMPLATES
description ...................................................................... 4-4
editing ............................................................................ 4-4
enabling.......................................................................... 4-4
Modbus registers........................................................... B-76
password protection ........................................................ 4-5
removing......................................................................... 4-7
viewing ........................................................................... 4-6
SETTINGS, CHANGING....................................................4-26
SIGNAL LOSS DETECTION FOR FIBER ...........................5-31
SIGNAL SOURCES
description ...................................................................... 5-5
metering ........................................................................6-17
settings..........................................................................5-96
SIGNAL TYPES ................................................................. 1-3
SINGLE LINE DIAGRAM ............................................. 2-1, 2-2
SITE LIST, CREATING ...................................................... 4-1
SNTP PROTOCOL
accuracy ........................................................................2-27
error messages ............................................................... 7-9
Modbus registers........................................................... B-28
settings..........................................................................5-62
SOFTWARE
installation ...................................................................... 1-6
see entry for ENERVISTA UR SETUP
SOFTWARE ARCHITECTURE............................................ 1-5
SOFTWARE, PC
see entry for EnerVista UR Setup
SOURCE FREQUENCY ....................................................6-20
SOURCE TRANSFER SCHEMES ....................................5-222
SOURCES
description ...................................................................... 5-5
example use of...............................................................5-97
metering ........................................................................6-17
settings.................................................................5-95, 5-96
SPECIFICATIONS ............................................................2-15