GE NetworX Series Installation And Start-Up Manual

NX-8E CONTROL
17
LOCATION 16 - EVENTS REPORTED TO PHONE #3 (2 segments, feature selection data)
Segment 1: 1 = Alarms and Alarm Restores.
2 = Opening and Closings.
3 = Zone Bypass and Bypass Restores.
4 = Zone Trouble and Trouble Restores.
5 = Power Fail, Low Battery, Power Restore, and Low Battery Restore.
6 = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore.
7 = Test Reports.
8 = Start and End programming, Download complete.
Segment 2: 1 = Zone and Box Tamper and Tamper Restore.
2 = Auxiliary Power Overcurrent and Ground Fault and Restore for both.
3 = Sensor Missing and Restore.
4 = Sensor Low Battery and Restore.
5 = Expander Trouble and Restore.
6 = Fail To Communicate.
7 = Zone Activity Monitor.
8 = Reserved.
LOCATION 17 - PARTITIONS REPORTED TO PHONE #3 (1 segment, feature selection data)
Location 17 is used when events to be reported to a phone number are based upon the partition regardless of the
event. If this location is used, location 16 should be "0".
Segment 1: 1 = Partition #1
2 = Partition #2
3 = Partition #3
4 = Partition #4
5 = Partition #5
6 = Partition #6
7 = Partition #7
8 = Partition #8
LOCATION 18 - CUSTOM COMMUNICATOR FORMAT (See locations 2, 8, &14)
Segment 1: 1 = On for 1800hz transmit; Off for 1900hz.
2= On for 2300hz handshake; Off for 1400hz.
3= On for cksum parity; Off for double round parity.
4= On for 2 digit event code; Off for 1 digit event code.
5= Reserved.
6= Reserved.
7= On for 20 p.p.s.; Off for 10 or 40 p.p.s.
8= On for 10 p.p.s.; Off for 20 or 40 p.p.s.
Segment 2: 1= On for pager format (no handshake required).
2= On for 1400/2300 handshake.
3= Reserved
4= Reserved.
5= On for Contact ID.
6= On for SIA.
7= On for Contact ID or 4+3.
8= On for DTMF.
Segment 3 & 4: Reserved.
L LOCATION 19 - DOWNLOAD ACCESS CODE (8 segments, numerical data)
Location 19 contains the eight-digit access code the NX-8E must receive from the downloading software before the
panel will permit downloading to occur. The factory default code is 84800000.
L LOCATION 20 - NUMBER OF RINGS TO ANSWER (1 segment, numerical data)
Location 20 contains the number of rings to answer for a download. Enter a number from A0" (disabled) to "15".
Factory default is "8" and the NX-8E will answer on 8 rings.

GE NetworX Series Specifications

General

Model	NetworX Series
Zones	Varies by model (e.g., 8, 16, 32, 64)
Partitions	Varies by model (typically 1-8)
Keypads	Supports multiple keypads
Communication	Phone line, cellular, IP
Power Supply	16.5 VAC
Backup Battery	12VDC, 7AH
User Codes	Varies by model (e.g., 48, 150, 300)
Event Buffer	Varies by model (e.g., 200, 500, 1000 events)
Operating Temperature	0°C to 49°C (32°F to 120°F)
Communication Protocol	Contact ID, SIA
Weight	Varies by model
Dimensions	Varies by model (e.g., 14.5" x 12.5" x 3.5")