SLOW COMMUNICATOR FORMAT CODES
NX-8E CONTROL
28
LOCATION 64 - KEYPAD AUXILIARY 2 COMMUNICATOR CODE (2 segments, numerical data)
Location 64 contains the digits that will be sent for a 4+2 format if the keypad "Auxiliary 2" (Medical) is enabled in the
partition feature selection. Refer to the box at the top of page 27.
LOCATION 65 - KEYPAD PANIC COMMUNICATOR CODE (2 segments, numerical data)
Location 65 contains the digits that will be sent for a 4+2 format if the keypad "Panic" is enabled in the partition feature
selection. Refer to the box at the top of page 27.
LOCATION 66 - KEYPAD MULTIPLE CODE ENTRY TAMPER COMMUNICATOR CODE (2 segments, numerical
data)
Location 66 contains the digits that will be sent for a 4+2 format if the keypad "Multiple Code Entry" (Tamper) is
enabled in the partition feature selection. Refer to the box at the top of page 27.
LOCATION 67 - BOX TAMPER / BOX TAMPER RESTORE COMMUNICATOR CODE (4 segments, numerical
data)
Location 67 contains the digits that will be sent for a 4+2 format if the "Box Tamper" feature is enabled in location 37.
Segments 1 & 2 contain the digits of the "Box Tamper". Segments 3 & 4 contain the digits of the "Box Tamper
Restore". Refer to the box at the top of page 27.
LOCATION 68 - AC FAIL / AC FAIL RESTORE COMMUNICATOR CODES (4 segments, numerical data)
Location 68 contains the digits for a 4+2 format that will be sent if "AC Fail Reporting" is enabled. Segments 1 & 2
contain the digits of the "AC Fail". Segments 3 & 4 contain the digits of the "AC Fail Restore". Refer to the box at the
top of page 27.
LOCATION 69 - LOW BATTERY / LOW BATTERY RESTORE COMMUNICATOR CODES, SLOW SPEED
FORMATS ONLY (4 segments, numerical data)
Location 69 contains the digits for a 4+2 format that will be sent if "Low Battery Reporting" is enabled. Segments 1 & 2
contain the digits of the "Low Battery Reporting". Segments 3 & 4 contain the digits of the "Low Battery Restore".
Refer to the box at the top of page 27.
LOCATION 70 - AUX POWER OVERCURRENT/ AUX POWER OVERCURRENT RESTORE COMMUNICATOR
CODES (4 segments, numerical data)
Location 70 contains the digits for a 4+2 format that will be sent if "Aux Power Overcurrent Reporting" is enabled.
Segments 1 & 2 contain the digits of the "Aux Power Overcurrent Reporting". Segments 3 & 4 contain the digits of the
"Aux Power Overcurrent Restore". Refer to the box at the top of page 27.
LOCATION 71 - BELL TAMPER / BELL TAMPER RESTORE COMMUNICATOR CODES (4 segments, numerical
data)
Location 71 contains the digits for a 4+2 format that will be sent if siren supervision reporting is enabled. Segments 1
& 2 contain the digits of the "Bell Tamper Reporting". Segments 3 & 4 contain the digits of the "Bell Tamper Restore".
Refer to the box at the top of page 27.
LOCATION 72 - TELEPHONE LINE CUT / TELEPHONE LINE CUT RESTORE COMMUNICATOR CODES (4
segments, numerical data)
Location 72 contains the digits for a 4+2 format that will be sent if "Telephone Line Cut Reporting" is enabled.
Segments 1 & 2 contain the digits of the "Telephone Line Cut Reporting". Segments 3 & 4 contain the digits of the
"Telephone Line Cut Restore". Refer to the box at the top of page 27.
LOCATION 73 - GROUND FAULT / GROUND FAULT RESTORE COMMUNICATOR CODES (4 segments,
numerical data)
Location 73 contains the digits for a 4+2 format that will be sent if "Ground Fault Reporting" is enabled, and the NX-
870 is installed. Segments 1 & 2 contain the digits of the "Ground Fault Reporting". Segments 3 & 4 contain the digits
of the "Ground Fault Restore". Refer to the box on page 27.
To Next Page
Loading...
