PA G E 1 4 I N S T R U C T I O N M A N U A L T X 4 5 0 0
5. Repeat steps 4 and 5 to enter all 5 digits as required.
The Selcall number is now ready to send.
6. Press and hold the CALL button. A long beep will be
heard and the radio will transmit the Selcall Ident.
NOTE: If the call is not sent within 10 seconds of
entering the last Ident digit the Call function will time-
out and the radio will return to normal mode. To exit
the
mode without sending the Selcall, briefly press
the CALL button.
Call acknowledge
If your Selcall transmission is successful, the radio you
called should respond with an ‘acknowledge’ signal -
usually two quick beeps. This will confirm to you that
the radio you called is now alerting its user to
your signal.
Selcall memories
Your radio is fitted with one ‘Call’ memory and 10 user
programmable Selcall memories labelled ‘C0’ to ‘C9’
There is also one additional location labelled ‘Id’.
Memory locations ‘C0’ to ‘C9’ are for storing frequently
called Selcall Idents. The additional location labelled ‘Id’
contains your radio’s own Selcall Ident. You should only
select this memory location if you need to change your
radio’s factory programmed Selcall Ident.
To store a Selcall Ident in memory
1. Briefly press the CALL button.
is displayed along
with the last sent or received Selcall Ident.
2. Rotate the Channel knob clockwise to select the
required Ident memory location ‘C0’ to ‘C9’ (or
select ‘Id’ to change your radios own Selcall Ident). If
an ALPHA label is displayed you will need to press F
then ALPHA to switch to Numeric mode.
3. Press and hold the Channel knob until the radio
beeps. The right-hand digit of the Selcall Ident
will flash.
4. Rotate the Channel knob to select the required
number in the flashing digit position.
5. Briefly press the Channel knob again to select the
next digit position.
6. Repeat steps 4 and 5 to enter all 5 digits as required.
7. Now press and hold the Channel knob. The entire
Ident will flash for a few seconds then the radio will
beep as the new Ident is stored.
e.g. Programming Call Memory C5
Recalling Selcall Idents
1. Briefly press the CALL button.
is displayed along
with the last sent or received Selcall Ident.
2. Rotate the Channel knob to select the required
Ident memory in locations ‘C0’ to ‘C9’.
3. Press and hold the CALL button to send the Ident.
Naming your Selcall Idents
Your radio allows you to label each Selcall Ident using
a 5 character name to make it easier to identify callers.
If an incoming Selcall matches one of those in your
radio’s memory, the label can be displayed instead of
the Selcall Ident.
NOTE: Before adding an ALPHA label to a Selcall Ident,
you must first store the required Ident in memory as
described left.
1. Briefly press the CALL button.
will be displayed
along with the last sent or received Selcall Ident.
2. Rotate the Channel knob to select the required
Ident memory in locations ‘C0’ to ‘C9’.
3. Briefly press the F then ALPHA to select the ALPHA
mode. ALPHA will be displayed briefly.
4. If the ALPHA label is empty, ‘- - - - -’ will be
displayed, otherwise it will display the last ALPHA
label programmed into that memory.
5. Press and hold the Channel knob until the radio
beeps. The left-hand position of the Alpha label will
flash.
6. Rotate the Channel knob to select the required
character in the flashing position then briefly press
the Channel knob again to select the next position.
7. Repeat step 6 to enter up to 5 characters
as required.
8. Now press and hold the Channel knob. The entire
Alpha label will flash for a few seconds then the
radio will beep as the label is stored.
To Next Page
Loading...
